Image IMHS81590 manual Rings Threaded Collar

Page 8

2.Orient the dry side jet pack (A) as shown and posi- tion it next to the three holes in the Inflatable Liner (29).

Attach the Temperature Probe Assembly (30) to the small hole in the Inflatable Liner (29). To do this, place the Temperature Probe Gasket (46) over the Probe connector threads. Insert the wire (not shown) through the hole, then push the Temperature Probe through the hole. Make sure the threads on the con- nector have been pushed fully through the vinyl liner. Thread the Temperature Probe Nut (47) onto the connector and make sure it is tight. Connect the wire from the Temperature Probe to the receptacle on the dry side jet pack (A).

3.Move the dry side jet pack (A) up against the wall of the tub. Pull the two connectors on the dry side jet pack through the large holes in the Inflatable Liner (29). Push a Wet Side Gasket (48) onto each con- nector. Thread a Wet Side Nut (49) onto each con- nector and make sure it is tight.

4.Position the wet side jet pack (B) as shown. Place an O-ring (52) in the groove of each connector on the wet side jet pack. Note: Make sure the O-rings are placed securely in the groove (see drawing 4A).

Attach the threaded collar on the right side (as seen on drawing 4A) of the wet side jet pack (B) to the corresponding connector on the dry side jet pack

(A). Attach the left side in the same manner. Note: If the threaded collars are not tightened fully, the spa will not function.

Position the Pillow (26) over the hole on the top of the wet side jet pack (B). Push the fasteners on the Pillow through the appropriate holes in the wet side jet pack.

8

2

 

Small

A

 

 

29

 

 

Hole

 

 

 

 

 

 

 

 

 

Receptacle

46

 

 

 

 

30

 

 

47

 

 

 

 

 

 

 

 

9

 

3

 

 

29

 

 

 

 

 

 

 

 

Connectors

A

 

 

 

 

 

 

48

 

 

 

49

48

 

 

 

 

 

 

 

 

 

9

4

 

 

 

 

 

 

 

O-rings (52)

A

 

 

 

 

 

 

26

 

 

 

B

 

 

 

29

 

 

 

 

4A

View of Inside of Wet Side Jet Pack

 

 

 

 

O-rings (52)

 

 

 

 

Threaded Collar

 

Image 8
Contents Model No. IMHS81590 Serial No Customer HOT LineTable of Contents Important Safety Instructions Read and Follow ALL InstructionsPage Before You Begin If you set up the Renew 815 inside If you set up the Renew 815 outsideChoosing a Location for the Hydrotherapy Spa An extension cord cannot be used with the RenewCross Section AssemblySchematic View from the Outside Rings Threaded Collar Page Using the Hydrotherapy Spa Testing and Treating the WaterPriming the SPA JET Unit Plugging in the RenewCleaning the Filter Heating System of Your SPASecuring the SPA Cover SPA JET Unit OperationDraining the Pump Using the ConsoleDraining the Renew Maintenance Trouble-shooting Symptom the SPA JET Unit Cavitates During USE Symptom the Water is not Being Cleaned by the FilterSymptom the Water Level Drops Symptom the Inflatable SPA Liner Loses AIRIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT Ordering Replacement PartsLimited 90 Day Massage Spa Warranty Location of the Spa Lit Pack Parts Bag Qty Description Part LISTÑModel No. IMHS81590Qty Description