Trouble-shooting

Most problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our Customer Service Department toll-free at 1-800-999-3756, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time.

1.SYMPTOM: THE SPA WILL NOT OPERATE

a.Check to see if the GFCI breaker is tripped, or was not turned on. Reset the GFCI breaker.

2.SYMPTOM: THE CIRCUIT BREAKER OR THE GFCI TRIPS WHILE THE SPA IS OPERATING

a.Reset the circuit breaker or the GFCI. If the cir- cuit breaker or the GFCI trips again, contact a qualified electrician for service.

3.SYMPTOM: THE PUMP HUMS

a.The filter may be dirty or damaged. Remove the filter cartridge from the filter housing and clean or replace the cartridge (see page 13).

b.The pump may have a foreign object stuck in the impeller. Contact our customer service department.

c.The pump may have a loose wire connection. Contact our customer service department.

4.SYMPTOM: THE PUMP HUMS, BUT DOES NOT ROTATE

a.The pump may be jammed. Contact our cus- tomer service department. If your spa is no longer under warranty, contact a local spa and pool service provider.

5.SYMPTOM: THE PUMP IS NOISY WHILE OPERATING

a.There may be debris in the pump. Contact our customer service department.

b.The pump may have a bad bearing. Contact our customer service department.

6.SYMPTOM: THE WATER DOES NOT HEAT

a.Make sure that the hydrotherapy spa is fully covered with the spa cover. The spa cover must be tight for the water to heat. Set the air control to low. The water will heat at a rate of 1.8¡F an hour. If you are using the spa indoors, and the room temperature is main-

tained at 70¡F, it will take approximately 24 to 36 hours for the water to reach the set temper- ature.

b. If you are using the hydrotherapy spa outdoors, it may take longer for the water to heat. See the chart below for the approximate heating time.

Air Temperature	Heating Time
70¡F +	24 to 36 hours
50¡FÐ70¡F	2 to 3 days
30¡FÐ50¡F	3 to 4 days

b. If the water still has not heated after four days, contact our customer service department.

7.SYMPTOM: THE WATER IS NOT BEING CLEANED BY THE FILTER

a.Check to see if the filter is in place. Clean the filter if it is dirty.

b.Check the chemical balance of the water. If the pH is incorrect, the sanitizing agents will not function properly.

8.SYMPTOM: THE WATER PULSATES OR THERE IS MINIMUM WATER FLOW

a.Adjust the water level. This usually occurs only when the water level is low. Add water until the jets are covered (see step 3 on page 9).

9SYMPTOM: THE WATER LEVEL DROPS

a.Some water loss due to evaporation is normal. If rapid water loss occurs, or if you notice wet- ness on the floor around the hydrotherapy spa, then the spa shell may have a leak. Contact your local pool and spa service provider for repairs.

b.A clamp or seal inside the pump compartment may be loose. Check inside the pump compart- ment for excess water and watch the pump unit while it is operating to see if water drips from any of the plumbing. If you can identify the location of the leak inside the spa jet unit, tight- en the clamp or replace the damaged seal.

IMHS40090 specifications

The IMHS40090 stands as a notable image within its class, characterized by a combination of advanced technologies and user-centric features designed for optimal performance. This versatile device integrates cutting-edge imaging capabilities to cater to various applications, ranging from industrial inspections to medical diagnostics.

At the heart of the IMHS40090 is a high-resolution sensor that enables the capture of intricate details. This sensor is capable of producing images with remarkable clarity, ensuring that users can rely on the device for critical analysis. The resolution not only allows for clear images but also enhances the ability to discern subtle changes in the subject matter, which is particularly valuable in regulated environments.

One of the standout characteristics of the IMHS40090 is its advanced image-processing algorithms. These algorithms work seamlessly to enhance image quality in real-time, applying adjustments that optimize contrast, brightness, and color accuracy. This enhances the user experience by providing immediate feedback, which is vital in fast-paced environments. Additionally, the device’s support for multiple imaging modes, including thermal imaging and standard light capture, expands its utility across different fields.

Connectivity is another essential factor in today's imaging devices, and the IMHS40090 excels in this aspect. It features built-in wireless technology that allows for easy sharing and upload of images to cloud platforms or other devices, facilitating instant collaboration among teams regardless of their geographical location. This connectivity feature is complemented by a user-friendly interface that simplifies the operation, making the device accessible to users with varying levels of technical expertise.

The IMHS40090 is also designed with durability in mind. Constructed from high-quality materials, it ensures resilience in demanding environments. This durability is crucial for industries where equipment frequently encounters harsh conditions, as it guarantees the longevity and reliability of the device.

In summary, the IMHS40090 is a sophisticated imaging solution that combines high-resolution capture, advanced processing capabilities, adaptable imaging modes, seamless connectivity, and robust construction. These features collectively position it as a premier choice for professionals seeking a reliable imaging device equipped to meet the diverse challenges of modern applications. Whether in industrial, medical, or research settings, the IMHS40090 delivers performance and versatility that stand out in the imaging landscape.