Image IMSB53950 user manual Choosing a Location for the Hydrotherapy Spa

Page 7

Choosing a Location for the Hydrotherapy Spa

There are many factors to consider when choosing a location to set up the hydrotherapy spa. These factors vary depending on whether you plan to use the spa inside or outside. We have listed several factors you may wish to consider as you decide where to set up the spa.

If you set up the hydrotherapy spa inside:

1.The spa will increase the level of humidity in your home. The location you choose should be well ventilated. You may need to install a ventilation fan or use a dehumidifier.

2.The spa should be located near a power source capable of supplying 240 volts AC power. It must be wired directly into a grounded circuit with a 45 amp circuit breaker and a Ground Fault Circuit Interrupter (GFCI) capable of carrying 45 amps. (See WIRING THE HYDROTHERAPY SPA on page 8). No other appliance should be on the same circuit.

3.The spa should be close to a source of water.

4.Do not use the spa on carpet or other material that may be damaged by moisture. We recommend that you place the spa on a water- and stain-resis- tant, non-slip surface with a floor drain for any water that may splash from the spa.

5.Make sure that the location you choose is stable. It must be able to support the weight of the spa when it is filled with water, plus the weight of the occupants. The spa weighs approximately 3,300 pounds when it is filled with water.

6.Do not use the spa above a finished living area, due to the risk of water damage.

7.Make sure that there is room around the spa to permit servicing of the unit. The dimensions of the spa are 84” W x 84” L x 36” H. You should allow for this size when choosing the location.

8.The spa is not designed for in-floor installation. However, it is compatible with a deck system that is built flush with the top of the spa, provided you leave access to the motor for service.

9.Make sure to note any other considerations, such as aesthetics or privacy concerns, that may affect the safety or enjoyment of using the spa.

If you set up the hydrotherapy spa outside:

1.Check local building codes concerning the use of outdoor spas.

2.The spa should be located near a power source capable of supplying 240 volts AC power. It must be wired directly into a grounded circuit with a 45 amp circuit breaker and a Ground Fault Circuit Interrupter (GFCI) capable of carrying 45 amps. (See WIRING THE HYDROTHERAPY SPA on page 8). No other appliance should be on the same circuit.

3.The spa should be close to a source of water.

4.We recommend that you place the spa on a water- and stain-resistant, non-slip surface. Do not use the spa on rough or sharp surfaces such as gravel or wood chips.

5.Make sure that the location you choose is stable. It must be able to support the weight of the spa when it is filled with water, plus the weight of the occupants. The spa weighs approximately 3,300 pounds when it is filled with water.

6.Consider environmental factors such as rain, wind, shade, and sunlight.

7.You should be able to monitor the use of the spa from your home, to prevent unauthorized use by children. You may want to enclose the spa with a fence and self-latching gate to prevent unautho- rized use.

8.Make sure that there is room around the spa to permit servicing of the unit. The dimensions of the spa are 84” W x 84” L x 36” H. You should allow for this size when choosing the location.

9.The spa is not designed to be installed below ground level. However, it is compatible with a deck system that is built flush with the top of the spa, provided you leave access to the motor for ser- vice.

10.Make sure to note any other considerations, such as aesthetics or privacy concerns, that may affect the safety or enjoyment of using the spa.

7

Image 7
Contents Customer HOT Line Model No. IMSB53950 Serial NoPosting the Warning Sign Table of ContentsRead and Follow ALL Instructions Important Safety InstructionsPage Page LED Before You BeginIf you set up the hydrotherapy spa outside If you set up the hydrotherapy spa insideChoosing a Location for the Hydrotherapy Spa Option Wiring the Hydrotherapy SpaAssembly Molded fill line. Do not overfill the spa Priming the Pumps Using the Hydrotherapy SpaStarting the Hydrotherapy SPA Testing and Treating the WaterUsing the CD Player and the POP-UP Speakers Securing the SPA Cover on the SPAJet Layout Diagram Using the Controls Page Maintenance Changing the Filter Cycle Water ChemistryMaintaining the Proper PH Balance Sanitizing the Hydrotherapy SPADraining the Hydrotherapy SPA Replacing the LED Light Draining the PumpsWinter USE and Care Troubleshooting Symptom the Water Level Drops Key No. Qty Description Part List-Model No. IMSB53950Exploded Drawing-Model No. IMSB53950 Limited Warranty Ordering Replacement PartsIcon Health & FITNESS, INC., 1500 S W., LOGAN, UT