Trouble-shooting

Most problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further assistance is needed, call our Customer Service Department toll-free at 1-877-897-7493, Monday through Friday, 6 a.m. until 6 p.m. Mountain Time.

1.SYMPTOM: THE SPA WILL NOT OPERATE

a.Check to see if the GFCI breaker is tripped or was not turned on. Reset the GFCI breaker.

2.SYMPTOM: THE CIRCUIT BREAKER OR THE GFCI TRIPS WHILE THE SPA IS OPERATING

a.Reset the circuit breaker or the GFCI. If the cir- cuit breaker or the GFCI trips again, contact a qualified electrician for service.

3.SYMPTOM: THE PUMP HUMS

a.The filter may be dirty or damaged. Remove the filter from the filter housing and clean or replace the filter (see page 13).

b.The pump may have a foreign object stuck in the impeller. Contact our customer service department.

c.The pump may have a loose wire connection. Contact our customer service department.

4.SYMPTOM: THE PUMP HUMS, BUT DOES NOT ROTATE

a.The pump may be jammed. Contact our cus- tomer service department. If your spa is no longer under warranty, contact a local spa and pool service provider.

5.SYMPTOM: THE PUMP IS NOISY WHILE OPERATING

a.There may be debris in the pump. Contact our customer service department.

b.The pump may have a bad bearing. Contact our customer service department.

6.SYMPTOM: THE WATER DOES NOT HEAT

a.Make sure that the hydrotherapy spa is fully covered with the spa cover. The spa cover must be tight for the water to heat. Set the air control to low. The water will heat at a rate of 6°F per hour. If you are using the spa indoors and the room temperature is main-

tained at 70°F, it will take approximately 6 to 8 hours for the water to reach the set tempera- ture.

b. If you are using the hydrotherapy spa outdoors, it may take longer for the water to heat. See the chart below for the approximate heating time.

Air Temperature	Heating Time
70'F +	6 to 8 hours
50'F - 70'F	9 to 11 hours
30'F - 50'F	12 to 14 hours

b. If the water still has not heated after four days, contact our customer service department.

7.SYMPTOM: THE WATER IS NOT BEING CLEANED BY THE FILTER

a.Check to see if the filter is in place. Clean the filter if it is dirty.

b.Check the chemical balance of the water. If the pH is incorrect, the sanitizing agents will not function properly.

8.SYMPTOM: THE WATER PULSATES OR THERE IS MINIMUM WATER FLOW

a.This usually occurs only when the water level is low. Add water until the jets are covered (see step 5 on page 9).

9.SYMPTOM: THE WATER LEVEL DROPS

a.Some water loss due to evaporation is normal. If rapid water loss occurs, or if you notice wet- ness on the floor around the hydrotherapy spa, the spa shell may have a leak. Contact your local pool and spa service provider for repairs.

b.A clamp or seal inside the pump compartment may be loose. Check inside the pump compart- ment for excess water and watch the pump unit while it is operating to see if water drips from any of the plumbing. If you can identify the location of the leak inside the spa jet unit, tight- en the clamp or replace the damaged seal.

IMHS63100 specifications

The Image IMHS63100 represents a significant advancement in the world of imaging technology, catering specifically to high-performance applications in various industries. It is designed to meet the stringent requirements of professional imaging, offering a blend of exceptional features and cutting-edge technologies.

At its core, the IMHS63100 is equipped with a high-resolution sensor that delivers stunning image clarity and detail. With a pixel count that exceeds 30 megapixels, it enables users to capture images that are not only sharp but also rich in color depth and dynamic range. This high resolution is essential for applications such as medical imaging, industrial inspection, and scientific research, where precision and detail are paramount.

One of the standout characteristics of the IMHS63100 is its advanced noise reduction capabilities. Utilizing sophisticated algorithms, the device minimizes noise without sacrificing image quality, ensuring that even in low-light conditions, the images remain clear and usable. This feature is particularly beneficial for users working in environments with fluctuating lighting, allowing for consistent performance and reliability.

In terms of connectivity, the IMHS63100 supports multiple interfaces, including USB 3.0 and GigE, which streamline the integration process into existing systems. This versatility allows it to be used seamlessly with various software platforms, enhancing the overall workflow efficiency. Additionally, the camera supports Power over Ethernet (PoE), simplifying installation and reducing cable clutter in complex setups.

The IMHS63100 is also designed with robust build quality in mind. Its durable casing makes it suitable for demanding environments, ensuring longevity and reliable operation in fields such as manufacturing and research laboratories. The camera's compact form factor further enhances its versatility, allowing it to be easily mounted in tight spaces without compromising performance.

Furthermore, the device incorporates intelligent features such as automated image processing and real-time analytics, enabling users to optimize workflows and make informed decisions based on accurate data. With these capabilities, the IMHS63100 is not just an imaging device but a comprehensive solution tailored to meet the nuanced demands of various high-performance applications.

In conclusion, the Image IMHS63100 is a powerful imaging system that combines high-resolution capabilities, advanced noise reduction, versatile connectivity options, and robust design to meet the needs of professional users. Whether in medical, industrial, or research applications, it stands as a reliable choice for those seeking superior image quality and performance.