Porter-Cable T550 instruction manual Storage, Engine Preparation, Generator

Page 14

STORAGE

If you are going to store your generator for more than 30 days, use the following information as a guide to prepare the generator for storage.

Never store generator with fuel in the tank indoors or in enclosed, poorly ventilated areas, where fumes can reach an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or other gas appliances.

Engine Preparation

1.Add fuel stabilizer to fuel tank to minimize the formation of fuel gum deposits during storage.

2.Run engine at least 5 minutes after adding stabi- lizer to allow it to enter the fuel system.

3.Next shut off engine.

4.Disconnect the spark plug wire and remove the spark plug.

5.Add one teaspoon of oil through the spark plug hole.

6.Place rag over spark plug hole and pull the recoil a few times to lubricate the combustion chamber.

7.Replace the spark plug, but do not connect the spark plug wire.

NOTE: If a fuel stabilizer is not used, all gasoline must be drained from the tank and carburetor to prevent gum deposits from forming on these parts and causing possible malfunction of the engine.

Generator

•Clean the generator as outlined in the Maintenance Section on this manual.

•Check that cooling air slots and openings on generator are open and unobstructed.

14 — ENG

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Instruction Manual Generator Specification T550Warranty This Warranty is not Transferable and does not CoverHazard What could Happen HOW to Prevent IT Safety Guidelines DefinitionsImportant Safety Instructions Risk of Electrocution and FireOperation of generator in rain Wet, icy, or flooded conditionsDoors or in ANY Confined Risk of FireDo not Operate Unit AreaRisk of Breathing Inhalation Hazard Generator Risk of Unsafe OperationListed voltage surge protec Risk from Lifting Risk of HOT SurfacesRisk of Moving Parts Grounding the Generator AssemblyRemove Generator from Carton Obtaining Electricity from the GeneratorOperation Connecting Electrical Loads Stopping EngineGenerator Maintenance MaintenanceEngine Maintenance Customer Responsibilities TableGenerator StorageEngine Preparation Wattage Calculations Running Watts Starting WattsStarting Wattage Requirements Volts X Amp = Watts Volts x 10 amps = 1200 wattsHousehold Wattage Calculator Appliance or Load Device Typical Device Wattage TotalTroubleshooting Guide Problem Cause CorrectionENG Generator Quick Facts

T550 specifications

The Porter-Cable T550 is a versatile and powerful tool designed for both professional and DIY users. Known for its robust performance and durability, the T550 stands out in the realm of pneumatic brad nailers. This tool is crafted to handle a variety of fastening tasks, making it an excellent choice for carpenters, woodworkers, and hobbyists alike.

One of the primary features of the Porter-Cable T550 is its lightweight and compact design. Weighing in at just over three pounds, it is easy to maneuver, reducing user fatigue during extended use. The design is also optimized for balance, ensuring that users can work efficiently in tight spaces or overhead applications without straining.

The T550 is equipped with a powerful engine that delivers consistent performance, allowing it to handle a wide range of materials, from softwoods to harder species. It fires 18-gauge brad nails ranging from 1 to 2 inches in length, providing flexibility for various projects. The tool's quick-release nose also simplifies jam clearing, ensuring minimal downtime and uninterrupted workflow.

Another noteworthy aspect of the Porter-Cable T550 is its adjustable depth control. This feature allows users to set the precise depth of each nail for perfect placement, ensuring that nails are set flush with the surface of the material. This is particularly beneficial for projects that require a neat finish, as it prevents any damage to the workpiece or visible nail heads.

The T550 is designed with an integrated air filter, which helps to keep dust and debris from entering the mechanism. This ensures long-term reliability and reduces maintenance needs. Additionally, its 360-degree exhaust port is adjustable, directing exhaust away from the user and the workpiece to maintain a clean working environment.

Safety is a key consideration in the design of the Porter-Cable T550. It features a sequential firing mechanism that prevents accidental firing, providing users peace of mind. Coupled with its non-marring nose tip, the tool minimizes the risk of damage to the work surface.

In summary, the Porter-Cable T550 brad nailer combines lightweight design, robust performance, and user-friendly features, making it a standout choice for anyone in need of a reliable fastening tool. Whether tackling home improvement projects or professional-grade carpentry, the T550 delivers precision and efficiency.
Top Page Image Contents