Porter-Cable T550 instruction manual Generator Quick Facts

Page 20

Generator Quick Facts

CALL 1-888-559-8550 TO FIND A LOCAL AUTHORIZED SERVICE CENTER NEAR YOU FOR REPAIRS AND SERVICE PART PURCHASES

ENGINE

Use clean, fresh gasoline with a minimum 87 octane rating. Do not add gasoline

GAS

during or immediately after use.

 

 

ENGINE

Refer to engine owner's manual for oil recommendations.

 

OIL

Most generators are equipped with a low-oil shutdown. If the oil is low or if the

 

Generator is not level, the engine will not start.

 

 

WATTAGE

Make wattage calculations before use. Refer to general operator's manual for further

instructions.

 

 

 

WIRING

Contact an electrician for any wiring instructions. If wiring into a house, a double-throw

transfer switch and a heavy duty cord set must be used.

 

 

 

 

Use a standard (12V) lawn and garden battery with a minimum of 45 A.H. or 210 CCA.

 

 

BATTERY

The voltage and frequency are regulated by the rpm’s of the engine. Do not adjust the

throttle or governor to achieve higher performance. This will only alter the factory Pre-

VOLT

set settings and damage anything connected to the generator.

REG.

 

 

 

 

Be sure a volt/amp surge protector is used when sensitive electronic equipment is

 

used, such as: televisions, computers, stereos, and etc… The damage of such

 

equipment without the use of a protector WILL NOT be covered under warranty.

ENGINE

Do not adjust or attempt maintenance without consulting engine manual or an

authorized engine service center.

 

Add stabilizer to fuel tank and run engine for 5 minutes before storage.

STORAGE

When in long term storage, operate the generator every 60 days for at least 10 minutes

with a load on it. This will prevent the loss of residual magnetism that produces the

 

 

electricity.

 

Allow the generator to run 5 minutes at no load for the engine and the genhead to

 

stabilize.

OPERATION

Make sure the adequate size of extension cord is used. Refer to the Grounding

 

Instructions/Extension Cord section of the owners manual.

 

If the generator is operating equipment that is drawing half of the rated watts it is

 

considered 50% load. Using all of the rated watts is considered 100% load.

 

ALWAYS REFER TO THE MANUALS SUPPLIED WITH THIS UNIT

 

 

 

Porter-Cable Corporation

 

4825 Highway 45 North

 

P.O. Box 2468

 

Jackson, TN 38302-2468

 

1-888-559-8550

20 — ENG

Page 19 Page 20
Image 20
Page 19 Page 20
Contents Instruction Manual Generator Specification T550Warranty This Warranty is not Transferable and does not CoverSafety Guidelines Definitions Important Safety InstructionsHazard What could Happen HOW to Prevent IT Risk of Electrocution and FireOperation of generator in rain Wet, icy, or flooded conditionsRisk of Fire Do not Operate UnitDoors or in ANY Confined AreaRisk of Breathing Inhalation Hazard Generator Risk of Unsafe OperationListed voltage surge protec Risk from Lifting Risk of HOT SurfacesRisk of Moving Parts Assembly Remove Generator from CartonGrounding the Generator Obtaining Electricity from the GeneratorOperation Connecting Electrical Loads Stopping EngineMaintenance Engine MaintenanceGenerator Maintenance Customer Responsibilities TableGenerator StorageEngine Preparation Wattage Calculations Running Watts Starting WattsStarting Wattage Requirements Volts X Amp = Watts Volts x 10 amps = 1200 wattsHousehold Wattage Calculator Appliance or Load Device Typical Device Wattage TotalTroubleshooting Guide Problem Cause CorrectionENG Generator Quick Facts

T550 specifications

The Porter-Cable T550 is a versatile and powerful tool designed for both professional and DIY users. Known for its robust performance and durability, the T550 stands out in the realm of pneumatic brad nailers. This tool is crafted to handle a variety of fastening tasks, making it an excellent choice for carpenters, woodworkers, and hobbyists alike.

One of the primary features of the Porter-Cable T550 is its lightweight and compact design. Weighing in at just over three pounds, it is easy to maneuver, reducing user fatigue during extended use. The design is also optimized for balance, ensuring that users can work efficiently in tight spaces or overhead applications without straining.

The T550 is equipped with a powerful engine that delivers consistent performance, allowing it to handle a wide range of materials, from softwoods to harder species. It fires 18-gauge brad nails ranging from 1 to 2 inches in length, providing flexibility for various projects. The tool's quick-release nose also simplifies jam clearing, ensuring minimal downtime and uninterrupted workflow.

Another noteworthy aspect of the Porter-Cable T550 is its adjustable depth control. This feature allows users to set the precise depth of each nail for perfect placement, ensuring that nails are set flush with the surface of the material. This is particularly beneficial for projects that require a neat finish, as it prevents any damage to the workpiece or visible nail heads.

The T550 is designed with an integrated air filter, which helps to keep dust and debris from entering the mechanism. This ensures long-term reliability and reduces maintenance needs. Additionally, its 360-degree exhaust port is adjustable, directing exhaust away from the user and the workpiece to maintain a clean working environment.

Safety is a key consideration in the design of the Porter-Cable T550. It features a sequential firing mechanism that prevents accidental firing, providing users peace of mind. Coupled with its non-marring nose tip, the tool minimizes the risk of damage to the work surface.

In summary, the Porter-Cable T550 brad nailer combines lightweight design, robust performance, and user-friendly features, making it a standout choice for anyone in need of a reliable fastening tool. Whether tackling home improvement projects or professional-grade carpentry, the T550 delivers precision and efficiency.
Top Page Image Contents