Porter-Cable D26729-028-0 instruction manual Stopping Engine

Page 12

Engine speed has been factory set to provide safe operation. Tampering with the engine speed adjustment could result in over-

heating of attachments and could cause a fire. Never attempt to “speed-up” the en- gine to obtain more performance. Both the output voltage and frequency will be thrown out of standard by this practice, endangering attachments and the user.

You MUST unplug any load from the generator before starting to prevent permanent damage to any appliances.

TO START THE ENGINE

Never run engine indoors or in enclosed, poor ventilated areas, engine exhaust contains carbon monoxide, an odorless and deadly gas.

1.On the engine there is a ON/OFF switch located on the front panel of the engine. Place this switch to the "ON" position

2.Push primer button three times. Wait two seconds between each push. In cold weather (50ºF/10ºC or below) push five times.

NOTE: Primer may be needed to restart a warm engine after a short shutdown.

3.Grasp handle on rope starter and pull slowly until resistance is felt. Let the rope rewind slowly. Pull rope with a rapid full arm stroke. Let rope rewind slowly. Repeat if necessary.

IMPORTANT: Allow generator to run at no load for 5 minutes upon each initial start-up to allow engine and generator to stabilize.

STOPPING ENGINE

1.Disconnect all electrical loads.

2.Turn ON/OFF switch to "OFF" position.

D26729

12- ENG

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Generator Consumer General and Service Information Consumer Safety InformationSafety Guidelines / Definitions Important Safety InstructionsWhen installing a Double Risk of Electrocution and FireWhen damaged Risk of Electrocution and FireOperation Generator in rainRisk of Fire Unit Indoors or in ANYConfined Area Risk of Breathing Inhalation Hazard Risk of Unsafe OperationRisk of HOT Surfaces Specifications Risk of Moving PartsRisk from Lifting Assembly Remove Generator from CartonOther Loose Parts Grounding the GeneratorDouble Throw Transfer Switch Obtaining Electricity from the GeneratorExtension Cords Operation Stopping Engine Connecting Electrical Loads Maintenance Engine MaintenanceGenerator Maintenance Customer Responsibilities TableStorage Engine PreparationGenerator Wattage Calculations Determining Wattage RequirementsApplication Guide Starting Wattage RequirementsHousehold Wattage Calculator Appliance or Load Device Typical Device Wattage TotalTroubleshooting Guide StartLimited Warranty Responsibility of Original Purchaser initial UserENG D26729 Quick Facts

D26729-028-0 specifications

The Porter-Cable D26729-028-0 is a powerful and versatile oscillating tool designed for professionals and DIY enthusiasts alike. Known for its robust functionality, the tool enhances precision and efficiency in various applications ranging from cutting to sanding. With a dedicated focus on user needs, the D26729 model embodies the blend of innovative technology and dependable craftsmanship that Porter-Cable is renowned for.

One of the standout features of the D26729-028-0 is its powerful motor. The 3.0-amp motor delivers consistent performance, making it suitable for demanding tasks while ensuring minimal downtime between projects. This ensures that users can tackle a variety of materials, including wood, metal, and plaster, with ease. The variable speed control allows for customization of the oscillation frequency, offering users the ability to adjust the tool’s performance based on the specific application and material, ensuring optimal results every time.

The tool’s design emphasizes ergonomics, featuring a user-friendly grip and lightweight build that minimizes fatigue during extended use. This thoughtful design enables greater control and comfort, allowing users to maintain focus and precision throughout their tasks. The quick-change accessory system is another significant characteristic of the D26729-028-0, enabling users to swiftly switch between accessories without the need for tools. This feature increases workflow efficiency and allows for easy transitions between different applications, such as sanding or cutting.

Durability is a key aspect of the Porter-Cable D26729-028-0, constructed with high-quality materials that can withstand the rigors of professional use. The device is also designed to reduce vibrations during operation, enhancing comfort and control. Its dust collection feature ensures a cleaner working environment by minimizing debris spread, further contributing to the tool’s overall user-centric design.

Additionally, the D26729 model is compatible with a wide array of accessories, making it a flexible addition to any toolbox. This compatibility extends the functionality of the tool, allowing it to serve multiple purposes in various projects, from home improvement to intricate woodworking tasks.

In summary, the Porter-Cable D26729-028-0 oscillating tool combines power, precision, and user-friendly features, making it an essential tool for both professionals and hobbyists. With its advanced technologies and robust design, it caters to a broad spectrum of applications, enhancing productivity while ensuring optimal results.
Top Page Image Contents