Porter-Cable D27243-028-0 instruction manual Storage, Engine Preparation, Generator

Page 16

STORAGE

If you are going to store your generator for more than 30 days, use the following information as a guide to prepare the generator for storage.

Never store generator with fuel in the tank indoors or in enclosed, poorly ventilated areas, where fumes can reach

an open flame, spark or pilot light as on a furnace, water heater, clothes dryer or other gas appliances.

ENGINE PREPARATION

1.Add fuel stabilizer to fuel tank to minimize the formation of fuel gum deposits during storage.

2.Run engine at least 10 minutes after adding stabilizer to allow it to enter the fuel system.

3.Next shut off engine.

4.Disconnect the spark plug wire and remove the spark plug.

5.Add one teaspoon of oil through the spark plug hole.

6.Place rag over spark plug hole and pull the recoil a few times to lubricate the combustion chamber.

7.Replace the spark plug, but do not connect the spark plug wire.

NOTE: If a fuel stabilizer is not used, all gasoline must be drained from the tank and carburetor to prevent gum deposits from forming on these parts and causing possible malfunction of the engine.

GENERATOR

•Clean the generator as outlined in the Maintenance Section on this manual.

•Check that cooling air slots and openings on generator are open and unobstructed.

D27243

16- ENG

Page 15 Page 17
Image 16
Page 15 Page 17
Contents Generator Consumer General and Service Information Consumer Safety InformationSafety Guidelines / Definitions Important Safety InstructionsWhen installing a Double Risk of Electrocution and FireWhen damaged Risk of Electrocution and FireOperation Generator in rainUnit Indoors or in ANY Risk of FireConfined Area Risk of Breathing Inhalation Hazard Risk of Unsafe OperationRisk of HOT Surfaces Risk of Moving Parts SpecificationsRisk from Lifting Assembly Remove Generator from CartonOther Loose Parts Grounding the GeneratorObtaining Electricity from the Generator Double Throw Transfer SwitchExtension Cords Operation 12V DC Outlet Before Start UPTo Start the Engine Connecting Electrical Loads Stopping EngineMaintenance Engine MaintenanceGenerator Maintenance Customer Responsibilities TableEngine Preparation StorageGenerator Wattage Calculations Determining Wattage RequirementsApplication Guide Starting Wattage RequirementsHousehold Wattage Calculator Appliance or Load Device Typical Device Wattage TotalTroubleshooting Guide StartLimited Warranty Responsibility of Original Purchaser initial UserQuick Facts

D27243-028-0 specifications

The Porter-Cable D27243-028-0 is a powerful and versatile tool designed for professional woodworkers and DIY enthusiasts alike. This exceptional tool combines advanced technologies, exceptional ergonomics, and powerful performance to help users achieve precise results with ease.

One of the standout features of the D27243-028-0 is its robust motor. Equipped with a high-performance motor, this tool delivers a consistent and reliable output, allowing craftsmen to tackle even the most demanding projects without breaking a sweat. This motor provides adequate power, making it suitable for various applications, including shaping, smoothing, and trimming.

The D27243-028-0 also boasts a variable speed control feature, enabling users to adjust the tool's speed to match the specific requirements of different tasks. This level of control is crucial for achieving precision in woodworking, as different materials and cutting techniques may require varying speeds for optimal results. The variable speed range ensures that users can seamlessly transition between different tasks while maintaining accuracy.

Additionally, comfort during operation is paramount, and the Porter-Cable D27243-028-0 excels in this aspect. The tool features an ergonomic design, complete with comfortable grips that minimize hand fatigue during prolonged use. This thoughtful design consideration allows users to work longer while reducing the risk of strain or discomfort.

The D27243-028-0 also supports efficient dust management, an essential feature in any woodworking application. The integrated dust collection system helps keep the workspace clean by capturing sawdust and debris as users work. This not only boosts visibility but also enhances safety, as a clean workspace reduces the chances of slips and accidents.

Durability is another hallmark of the Porter-Cable D27243-028-0. Built with high-quality materials, this tool is designed to withstand the rigors of professional use. Its rugged construction ensures longevity, providing users with a solid investment that will serve them well over time.

Overall, the Porter-Cable D27243-028-0 stands as a testament to the brand's commitment to delivering top-notch tools that blend power, precision, and comfort. Whether you're a seasoned professional or a passionate hobbyist, this tool equips you with the capability to bring your woodworking projects to life with accuracy and ease.
Top Page Image Contents