Porter-Cable D27243-028-0 instruction manual Quick Facts

Page 22

QUICK FACTS

CALL 1-888-559-8550 TO FIND A LOCAL AUTHORIZED SERVICE CENTER NEAR YOU FOR REPAIRS AND SERVICE PART PURCHASES

ENGINE

GAS

ENGINE OIL

WATTAGE

WIRING

BATTERY

VOLT REG.

ENGINE

STORAGE

OPERATION

Use clean, fresh gasoline with a minimum 87 octane rating. Do not add gasoline during or immediately after use.

Refer to engine owner's manual for oil recommendations. Most generators are equipped with a low-oil shutdown. If the oil is low or if the Generator is not level, the engine will not start.

Make wattage calculations before use. Refer to general operator's manual for further instructions.

Contact an electrician for any wiring instructions. If wiring into a house, a double-throw transfer switch and a heavy duty cord set must be used.

Use a standard (12V) lawn and garden battery with a minimum of 45 A.H. or 210 CCA.

The voltage and frequency are regulated by the rpm's of the engine. Do not adjust the throttle or governor to achieve higher performance. This will only alter the factory Pre-set settings and damage anything connected to the generator.

Be sure a volt/amp surge protector is used when sensitive electronic equipment is used, such as: televisions, computers, stereos, and etc… The damage of such equipment without the use of a protector WILL NOT be covered under warranty.

Do not adjust or attempt maintenance without consulting engine manual or an authorized engine service center.

Add stabilizer to fuel tank and run engine for 5 minutes before storage.

When in long term storage, operate the generator every 60 days for at least 10 minutes with a load on it. This will prevent the loss of residual magnetism that produces the electricity.

Allow the generator to run 5 minutes at no load for the engine and the gen head to stabilize.

Make sure the adequate size of extension cord is used. Refer to the Grounding Instructions/Extension Cord section of the owners manual.

If the generator is operating equipment that is drawing half of the rated watts it is considered 50% load. Using all of the rated watts is considered 100% load.

ALWAYS REFER TO THE MANUALS SUPPLIED WITH THIS UNIT

D27243

22- ENG

Page 21 Page 22
Image 22
Page 21 Page 22
Contents Generator Consumer General and Service Information Consumer Safety InformationWhen installing a Double Safety Guidelines / DefinitionsImportant Safety Instructions Risk of Electrocution and FireOperation When damagedRisk of Electrocution and Fire Generator in rainUnit Indoors or in ANY Risk of FireConfined Area Risk of Breathing Inhalation Hazard Risk of Unsafe OperationRisk of HOT Surfaces Risk of Moving Parts SpecificationsRisk from Lifting Other Loose Parts AssemblyRemove Generator from Carton Grounding the GeneratorObtaining Electricity from the Generator Double Throw Transfer SwitchExtension Cords Operation 12V DC Outlet Before Start UPTo Start the Engine Connecting Electrical Loads Stopping EngineGenerator Maintenance MaintenanceEngine Maintenance Customer Responsibilities TableEngine Preparation StorageGenerator Wattage Calculations Determining Wattage RequirementsApplication Guide Starting Wattage RequirementsHousehold Wattage Calculator Appliance or Load Device Typical Device Wattage TotalTroubleshooting Guide StartLimited Warranty Responsibility of Original Purchaser initial UserQuick Facts

D27243-028-0 specifications

The Porter-Cable D27243-028-0 is a powerful and versatile tool designed for professional woodworkers and DIY enthusiasts alike. This exceptional tool combines advanced technologies, exceptional ergonomics, and powerful performance to help users achieve precise results with ease.

One of the standout features of the D27243-028-0 is its robust motor. Equipped with a high-performance motor, this tool delivers a consistent and reliable output, allowing craftsmen to tackle even the most demanding projects without breaking a sweat. This motor provides adequate power, making it suitable for various applications, including shaping, smoothing, and trimming.

The D27243-028-0 also boasts a variable speed control feature, enabling users to adjust the tool's speed to match the specific requirements of different tasks. This level of control is crucial for achieving precision in woodworking, as different materials and cutting techniques may require varying speeds for optimal results. The variable speed range ensures that users can seamlessly transition between different tasks while maintaining accuracy.

Additionally, comfort during operation is paramount, and the Porter-Cable D27243-028-0 excels in this aspect. The tool features an ergonomic design, complete with comfortable grips that minimize hand fatigue during prolonged use. This thoughtful design consideration allows users to work longer while reducing the risk of strain or discomfort.

The D27243-028-0 also supports efficient dust management, an essential feature in any woodworking application. The integrated dust collection system helps keep the workspace clean by capturing sawdust and debris as users work. This not only boosts visibility but also enhances safety, as a clean workspace reduces the chances of slips and accidents.

Durability is another hallmark of the Porter-Cable D27243-028-0. Built with high-quality materials, this tool is designed to withstand the rigors of professional use. Its rugged construction ensures longevity, providing users with a solid investment that will serve them well over time.

Overall, the Porter-Cable D27243-028-0 stands as a testament to the brand's commitment to delivering top-notch tools that blend power, precision, and comfort. Whether you're a seasoned professional or a passionate hobbyist, this tool equips you with the capability to bring your woodworking projects to life with accuracy and ease.
Top Page Image Contents