Poulan 183397 owner manual Interlocks and Relays, To Replace Fuse, To Adjust Carburetor

Page 25

SERVICE AND ADJUSTMENTS

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 31)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT WIRE

CONNECTOR

FIG. 31

ENGINE

TO ADJUST THROTTLE CONTROL CABLE (See Fig. 32)

The throttle control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move throttle control lever to fast position.

•Check that swivel is against stop. If it is not, loosen cable clamp screw and pull cable back until swivel is against stop. Tighten cable clamp screw securely.

TO ADJUST CHOKE CONTROL (See Fig. 33)

The choke control has been preset at the factory and adjustment should not be necessary. Check adjustment as described below before loosening cable. If adjustment is necessary, proceed as follows:

•With engine not running, move choke control (located on dash panel) to full choke position.

•Loosen knob and remove cover assembly from air cleaner.

•Choke should be closed. If it is not, loosen casing clamp screw and move choke cable until choke is completely closed. Tighten casing clamp screw securely.

•Replace air cleaner cover assembly and tighten knob.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

High speed stop is factory adjusted. Do not adjust - damage may result.

IMPORTANT: NEVER TAMPER WITH THE ENGINE GOVERNOR, WHICH IS FACTORY SET FOR PROPER ENGINE SPEED. OVERSPEEDING THE ENGINE ABOVE T H E F A C T O R Y H I G H S P E E D S E T T I N G C A N B E DANGEROUS. IF YOU THINK THE ENGINE-GOVERNED HIGH SPEED NEEDS ADJUSTING, CONTACT YOUR N E A R E S T A U T H O R I Z E D S E R V I C E C E N T E R / DEPARTMENT, WHICH HAS PROPER EQUIPMENT AND E X P E R I E N C E T O M A K E A N Y N E C E S S A R Y ADJUSTMENTS.

STOP

SWIVELCLAMP

SCREW

FIG. 32

CLAMP SCREW

FIG. 33

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents PPR20H42STC IV. Service Safety RulesGeneral Operation II. Slope OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsSlope Sheet Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingCheck Deck Levelness To Convert to Bagging or DischargingOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other Attach Before Starting the EngineMents Check Engine OIL LevelPurge Transmission Mowing TipsAutomatic Transmission Warm UP Mulching Mowing Tips Service Dates Lubrication ChartCustomer Responsibilities General RecommendationsBrake Operation TractorTires Operator Presence SystemEngine Clean AIR INTAKE/COOLING Areas Clean AIR ScreenCleaning MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingBelt Installation To Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERReplacing Battery See Figs To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Attach Jumper CablesInterlocks and Relays To Adjust CarburetorTo Replace Fuse Other StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PPR20H42STC SchematicElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly 180656 Wheel Steering KEY Part NO. NO. Description Seat AssemblyWheels and Tires DecalsOptional Equipment EngineSpark Arrester 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

183397 specifications

The Poulan 183397 is a robust and versatile chainsaw designed to meet the demands of both amateur woodworkers and professional loggers. Renowned for its power and reliability, this chainsaw has become a popular choice among users seeking efficiency and durability in their cutting tasks.

One of the standout features of the Poulan 183397 is its potent engine. Powered by a high-performance 18-inch engine, this chainsaw delivers exceptional cutting power, effortlessly tackling thick branches and large logs. The engine is designed with technology that maximizes fuel efficiency, ensuring that users can work longer without frequent refueling. This makes it an ideal option for extended trimming and clearing projects.

In addition to its powerful engine, the Poulan 183397 incorporates an effective air filtration system. This innovative feature helps to prolong the life of the engine by minimizing the amount of debris that enters it during operation. The air filter is easy to access and clean, allowing users to maintain their chainsaw with minimal hassle.

Another key technology integrated into the Poulan 183397 is its automatic oiling system. This feature ensures the chain remains well-lubricated during use, reducing friction and wear. With a properly lubricated chain, users can achieve smoother cuts and extend the life of their chainsaw. The oil reservoir is easily viewable, allowing users to monitor oil levels at a glance.

The design of the Poulan 183397 also focuses on user comfort and safety. It features an ergonomic handle with reduced vibration for optimal control, making it easier to handle for extended periods. Safety features include a chain brake, which instantly stops the chain in the event of kickback, providing peace of mind while operating.

Moreover, the Poulan 183397 is known for its easy start technology. This feature reduces the effort required to start the chainsaw, making it accessible for users of all experience levels. The chainsaw's lightweight design further enhances its usability, allowing for easier maneuverability in various cutting conditions.

In summary, the Poulan 183397 chainsaw is equipped with a powerful engine, effective air filtration, automatic oiling, and user-friendly features. Ideal for both casual users and professionals, it provides a perfect balance of performance, reliability, and safety, making it a valuable addition to any tool collection. Whether tackling yard work or larger cutting jobs, the Poulan 183397 is built to handle the task with ease and efficiency.
Top Page Image Contents