Poulan 183397 owner manual Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel Alignment

Page 23

SERVICE AND ADJUSTMENTS

ENGINE

PULLEY

CLUTCHING

IDLER

STATION-

ARY IDLER

TRANSMISSION

 

INPUT PULLEY

CENTER SPAN

 

KEEPER

FIG. 25

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “PURGE TRANSMIS- SION” in the Operation section of this manual.

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 26)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satisfied.

MOTION CONTROL

NEUTRAL

LOCK GATE

LEVER

 

 

ADJUSTMENT

 

BOLT

FIG. 26

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY

(REAR WHEEL ONLY)

FIG. 27

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents PPR20H42STC II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorInstall Seat See Fig To Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other Attach MentsAutomatic Transmission Warm UP Mowing TipsPurge Transmission Mulching Mowing Tips General Recommendations Lubrication ChartService Dates Customer ResponsibilitiesOperator Presence System TractorBrake Operation TiresEngine Muffler Clean AIR ScreenClean AIR INTAKE/COOLING Areas CleaningTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Replace Headlight BulbTo Replace Fuse To Adjust CarburetorInterlocks and Relays Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PPR20H42STC SchematicElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly 180656 Wheel Steering KEY Part NO. NO. Description Seat AssemblyWheels and Tires DecalsSpark Arrester EngineOptional Equipment 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

183397 specifications

The Poulan 183397 is a robust and versatile chainsaw designed to meet the demands of both amateur woodworkers and professional loggers. Renowned for its power and reliability, this chainsaw has become a popular choice among users seeking efficiency and durability in their cutting tasks.

One of the standout features of the Poulan 183397 is its potent engine. Powered by a high-performance 18-inch engine, this chainsaw delivers exceptional cutting power, effortlessly tackling thick branches and large logs. The engine is designed with technology that maximizes fuel efficiency, ensuring that users can work longer without frequent refueling. This makes it an ideal option for extended trimming and clearing projects.

In addition to its powerful engine, the Poulan 183397 incorporates an effective air filtration system. This innovative feature helps to prolong the life of the engine by minimizing the amount of debris that enters it during operation. The air filter is easy to access and clean, allowing users to maintain their chainsaw with minimal hassle.

Another key technology integrated into the Poulan 183397 is its automatic oiling system. This feature ensures the chain remains well-lubricated during use, reducing friction and wear. With a properly lubricated chain, users can achieve smoother cuts and extend the life of their chainsaw. The oil reservoir is easily viewable, allowing users to monitor oil levels at a glance.

The design of the Poulan 183397 also focuses on user comfort and safety. It features an ergonomic handle with reduced vibration for optimal control, making it easier to handle for extended periods. Safety features include a chain brake, which instantly stops the chain in the event of kickback, providing peace of mind while operating.

Moreover, the Poulan 183397 is known for its easy start technology. This feature reduces the effort required to start the chainsaw, making it accessible for users of all experience levels. The chainsaw's lightweight design further enhances its usability, allowing for easier maneuverability in various cutting conditions.

In summary, the Poulan 183397 chainsaw is equipped with a powerful engine, effective air filtration, automatic oiling, and user-friendly features. Ideal for both casual users and professionals, it provides a perfect balance of performance, reliability, and safety, making it a valuable addition to any tool collection. Whether tackling yard work or larger cutting jobs, the Poulan 183397 is built to handle the task with ease and efficiency.
Top Page Image Contents