Poulan 183397 Clean AIR Screen, Clean AIR INTAKE/COOLING Areas, Muffler, Spark Plugs, Cleaning

Page 19

CUSTOMER RESPONSIBILITIES

CLEAN AIR SCREEN

Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers.

CLEAN AIR INTAKE/COOLING AREAS

To insure proper cooling, make sure the grass screen, cooling fins, and other external surfaces of the engine are kept clean at all times.

Every 100 hours of operation (more often under extremely dusty, dirty conditions), remove the blower housing and other cooling shrouds. Clean the cooling fins and external surfaces as necessary. Make sure the cooling shrouds are reinstalled.

NOTE: Operating the engine with a blocked grass screen, dirty or plugged cooling fins, and/or cooling shrouds removed will cause engine damage due to overheating.

AIR FILTER (See Fig. 16)

Your engine will not run properly using a dirty air filter. Clean the foam pre-cleaner after every 25 hours of operation or every season. Service paper cartridge every 100 hours of operation or every season, whichever occurs first.

Service air cleaner more often under dusty conditions.

Remove knobs and cover.

TO SERVICE PRE-CLEANER

Wash it in liquid detergent and water.

Squeeze it dry in a clean cloth.

Saturate it in engine oil. Wrap it in clean, absorbent cloth and squeeze to remove excess oil.

If very dirty or damaged, replace pre-cleaner.

TO SERVICE CARTRIDGE

Clean cartridge by tapping gently on flat surface. If very dirty or damaged, replace cartridge.

Reinstall precleaner cartridge, cover and secure with knobs.

IMPORTANT: PETROLEUM SOLVENTS, SUCH AS KEROSENE, ARE NOT TO BE USED TO CLEAN THE CARTRIDGE. THEY MAY CAUSE DETERIORATION OF THE CARTRIDGE. DO NOT OIL CARTRIDGE. DO NOT USE PRESSURIZED AIR TO CLEAN OR DRY CARTRIDGE.

KNOBS

COVER

CARTRIDGE

FOAM

PRE-CLEANER

FIG. 16

MUFFLER

Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage.

SPARK PLUGS

Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICATIONS” section of this manual.

IN-LINE FUEL FILTER (See Fig. 17)

The fuel filter should be replaced once each season. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required.

With engine cool, remove filter and plug fuel line sec- tions.

Place new fuel filter in position in fuel line with arrow pointing towards carburetor.

Be sure there are no fuel line leaks and clamps are properly positioned.

Immediately wipe up any spilled gasoline.

CLAMP

CLAMP

 

FUEL

FILTER

FIG. 17

CLEANING

Clean engine, battery, seat, finish, etc. of all foreign matter.

Keep finished surfaces and wheels free of all gasoline, oil, etc.

Protect painted surfaces with automotive type wax.

We do not recommend using a garden hose to clean your tractor unless the electrical system, muffler, air filter and carburetor are covered to keep water out. Water in engine can result in a shortened engine life.

19

Image 19
Contents PPR20H42STC II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsSlope Sheet To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorInstall Seat See Fig To Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other Attach MentsPurge Transmission Mowing TipsAutomatic Transmission Warm UP Mulching Mowing Tips General Recommendations Lubrication ChartService Dates Customer ResponsibilitiesOperator Presence System TractorBrake Operation TiresEngine Muffler Clean AIR ScreenClean AIR INTAKE/COOLING Areas CleaningTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Replace Headlight BulbInterlocks and Relays To Adjust CarburetorTo Replace Fuse Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PPR20H42STC SchematicElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly 180656 Wheel Steering KEY Part NO. NO. Description Seat AssemblyWheels and Tires DecalsOptional Equipment EngineSpark Arrester 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

183397 specifications

The Poulan 183397 is a robust and versatile chainsaw designed to meet the demands of both amateur woodworkers and professional loggers. Renowned for its power and reliability, this chainsaw has become a popular choice among users seeking efficiency and durability in their cutting tasks.

One of the standout features of the Poulan 183397 is its potent engine. Powered by a high-performance 18-inch engine, this chainsaw delivers exceptional cutting power, effortlessly tackling thick branches and large logs. The engine is designed with technology that maximizes fuel efficiency, ensuring that users can work longer without frequent refueling. This makes it an ideal option for extended trimming and clearing projects.

In addition to its powerful engine, the Poulan 183397 incorporates an effective air filtration system. This innovative feature helps to prolong the life of the engine by minimizing the amount of debris that enters it during operation. The air filter is easy to access and clean, allowing users to maintain their chainsaw with minimal hassle.

Another key technology integrated into the Poulan 183397 is its automatic oiling system. This feature ensures the chain remains well-lubricated during use, reducing friction and wear. With a properly lubricated chain, users can achieve smoother cuts and extend the life of their chainsaw. The oil reservoir is easily viewable, allowing users to monitor oil levels at a glance.

The design of the Poulan 183397 also focuses on user comfort and safety. It features an ergonomic handle with reduced vibration for optimal control, making it easier to handle for extended periods. Safety features include a chain brake, which instantly stops the chain in the event of kickback, providing peace of mind while operating.

Moreover, the Poulan 183397 is known for its easy start technology. This feature reduces the effort required to start the chainsaw, making it accessible for users of all experience levels. The chainsaw's lightweight design further enhances its usability, allowing for easier maneuverability in various cutting conditions.

In summary, the Poulan 183397 chainsaw is equipped with a powerful engine, effective air filtration, automatic oiling, and user-friendly features. Ideal for both casual users and professionals, it provides a perfect balance of performance, reliability, and safety, making it a valuable addition to any tool collection. Whether tackling yard work or larger cutting jobs, the Poulan 183397 is built to handle the task with ease and efficiency.