Poulan 183255 To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 12

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 7)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

3/8-16

LOCKNUT

GUAGE WHEEL

MOUNTING

BRACKET

3/8 WASHER

SHOULDER

GAUGE WHEEL

BOLT

 

FIG. 7

TO OPERATE MOWER (See Fig. 8)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

"ENGAGED" POSITION

ATTACHMENT LIFT LEVER HIGH POSITION

ATTACHMENT

 

CLUTCH LEVER

LOW

"DISENGAGED"

POSITION

POSITION

 

DEFLECTOR

SHIELD

FIG. 8

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/BRAKE PEDAL IS DEPRESSED.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 5 and 9)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attach- ment lift control.

•Pull freewheel control out and down into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PPR20H42STB Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Table of Contents Unassembled Parts Steering Wheel SeatSlope Sheet Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig To SET UP Your Mower for Mulching Check Tire PressureCheck Deck Levelness To Convert to Bagging or DischargingOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other AttachMents Check Engine OIL LevelMowing Tips Purge TransmissionAutomatic Transmission Warm UP Mulching Mowing Tips Lubrication Chart Everybefore Service DatesCustomer Responsibilities General RecommendationsTractor Brake OperationTires Operator Presence SystemEngine Clean AIR Screen Clean AIR INTAKE/COOLING AreasCleaning MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing FRONT-TO-BACK Adjustment See FigsTo Adjust Brake See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT Transaxle Motion Control Lever Neutral Adjustment See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig Replacing Battery See FigsTo Replace Headlight Bulb To Attach Jumper CablesTo Adjust Carburetor Interlocks and RelaysTo Replace Fuse Storage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PPR20H42STBElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresEngine Optional EquipmentSpark Arrester 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

183255 specifications

The Poulan 183255 is a versatile and robust tool designed for homeowners and professionals alike, particularly suited for tackling lawn maintenance and light landscaping tasks. Known for its reliability and efficiency, the Poulan 183255 is equipped with an array of features that enhance its usability and performance.

One of its standout features is the powerful gas engine that ensures robust cutting performance. With a displacement of 25cc, the engine delivers impressive torque while maintaining fuel efficiency. The lightweight design of the unit makes it easy to handle, reducing user fatigue during prolonged use. One of the key characteristics of the Poulan 183255 is its ergonomic design, which includes a comfortable grip and adjustable handle, allowing for extended operation without discomfort.

The cutting head of the Poulan 183255 is designed for versatility, accommodating different types of attachments. This feature enables users to switch between trimming and edging tasks seamlessly, making it an ideal choice for maintaining a well-groomed lawn. The trimmer line is easy to replace, ensuring minimal downtime and allowing users to get back to work quickly.

Another notable technology in the Poulan 183255 is the Easy Start System, which reduces the effort required to start the machine. This system minimizes the time spent on starting and maximizes efficiency, allowing users to get straight to their trimming tasks without hassle. Additionally, the unit is built to minimize vibration, providing a smoother experience during operation and contributing to overall user comfort.

The Poulan 183255 also boasts a durable construction, making it suitable for various environments, from residential lawns to more challenging terrains. Its rugged design ensures longevity, even when faced with demanding tasks. Furthermore, maintenance is straightforward, with easily accessible parts that allow for quick repairs and service.

In summary, the Poulan 183255 is a powerful, versatile, and user-friendly trimmer that is ideal for anyone looking to maintain their yard with ease. With its reliable engine, ergonomic features, and advanced technologies, it stands out as a dependable choice for effective lawn care. Whether you’re a seasoned landscaper or a weekend warrior, the Poulan 183255 provides the performance and efficiency needed to get the job done right.
Top Page Image Contents