Poulan 183255 owner manual Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel Alignment

Page 23

SERVICE AND ADJUSTMENTS

ENGINE

PULLEY

CLUTCHING

IDLER

STATION-

ARY IDLER

TRANSMISSION

 

INPUT PULLEY

CENTER SPAN

 

KEEPER

FIG. 25

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See “PURGE TRANSMIS- SION” in the Operation section of this manual.

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 26)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine off.

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satisfied.

MOTION CONTROL

NEUTRAL

LOCK GATE

LEVER

 

 

ADJUSTMENT

 

BOLT

FIG. 26

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY

(REAR WHEEL ONLY)

FIG. 27

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents PPR20H42STB II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorInstall Seat See Fig To Convert to Bagging or Discharging To SET UP Your Mower for MulchingCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other Attach MentsAutomatic Transmission Warm UP Mowing TipsPurge Transmission Mulching Mowing Tips General Recommendations Lubrication ChartEverybefore Service Dates Customer ResponsibilitiesOperator Presence System TractorBrake Operation TiresEngine Muffler Clean AIR ScreenClean AIR INTAKE/COOLING Areas CleaningTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Motion Drive Belt See Fig To Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral Adjustment See Fig To Adjust Steering Wheel AlignmentTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Replace Headlight BulbTo Replace Fuse To Adjust CarburetorInterlocks and Relays Engine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PPR20H42STB SchematicElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly KEY Part NO. NO. Description Seat Assembly Wheels and Tires DecalsSpark Arrester EngineOptional Equipment 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

183255 specifications

The Poulan 183255 is a versatile and robust tool designed for homeowners and professionals alike, particularly suited for tackling lawn maintenance and light landscaping tasks. Known for its reliability and efficiency, the Poulan 183255 is equipped with an array of features that enhance its usability and performance.

One of its standout features is the powerful gas engine that ensures robust cutting performance. With a displacement of 25cc, the engine delivers impressive torque while maintaining fuel efficiency. The lightweight design of the unit makes it easy to handle, reducing user fatigue during prolonged use. One of the key characteristics of the Poulan 183255 is its ergonomic design, which includes a comfortable grip and adjustable handle, allowing for extended operation without discomfort.

The cutting head of the Poulan 183255 is designed for versatility, accommodating different types of attachments. This feature enables users to switch between trimming and edging tasks seamlessly, making it an ideal choice for maintaining a well-groomed lawn. The trimmer line is easy to replace, ensuring minimal downtime and allowing users to get back to work quickly.

Another notable technology in the Poulan 183255 is the Easy Start System, which reduces the effort required to start the machine. This system minimizes the time spent on starting and maximizes efficiency, allowing users to get straight to their trimming tasks without hassle. Additionally, the unit is built to minimize vibration, providing a smoother experience during operation and contributing to overall user comfort.

The Poulan 183255 also boasts a durable construction, making it suitable for various environments, from residential lawns to more challenging terrains. Its rugged design ensures longevity, even when faced with demanding tasks. Furthermore, maintenance is straightforward, with easily accessible parts that allow for quick repairs and service.

In summary, the Poulan 183255 is a powerful, versatile, and user-friendly trimmer that is ideal for anyone looking to maintain their yard with ease. With its reliable engine, ergonomic features, and advanced technologies, it stands out as a dependable choice for effective lawn care. Whether you’re a seasoned landscaper or a weekend warrior, the Poulan 183255 provides the performance and efficiency needed to get the job done right.
Top Page Image Contents