Poulan 183255 Before Starting the Engine, Towing Carts and Other Attach, Ments, ADD Gasoline

Page 13

OPERATION

 

 

CAUTION: Alcohol blended fuels (called

 

gasohol or using ethanol or methanol)

 

can attract moisture which leads to sepa-

 

ration and formation of acids during

 

storage. Acidic gas can damage the fuel

 

system of an engine while in storage. To

 

avoid engine problems, the fuel system

 

should be emptied before storage of 30

 

days or longer. Drain the gas tank, start

 

the engine and let it run until the fuel

 

lines and carburetor are empty. Use

 

fresh fuel next season. See Storage

 

Instructions for additional information.

FIG. 9

Never use engine or carburetor cleaner

TOWING CARTS AND OTHER ATTACH-

products in the fuel tank or permanent

damage may occur.

MENTS

 

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

•The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Customer Responsibilities section of this manual).

•To change engine oil, see the Customer Responsibilities section in this manual.

ADD GASOLINE

•Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

TO START ENGINE (See Fig. 5)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

•Place motion control lever in neutral (N) position.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to fast position

•Pull choke control out for a cold engine start attempt. For a warm engine start attempt the choke control may not be needed.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, push choke control in, wait a few minutes and try again. If engine still does not start, pull the choke control out and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50° F and below)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the engine to accept small changes in speed and load, until the choke control is fully in. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents PPR20H42STB IV. Service Safety RulesGeneral Operation II. Slope OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsSlope Sheet Tools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingCheck Deck Levelness To Convert to Bagging or DischargingOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other Attach Before Starting the EngineMents Check Engine OIL LevelPurge Transmission Mowing TipsAutomatic Transmission Warm UP Mulching Mowing Tips Everybefore Service Dates Lubrication ChartCustomer Responsibilities General RecommendationsBrake Operation TractorTires Operator Presence SystemEngine Clean AIR INTAKE/COOLING Areas Clean AIR ScreenCleaning MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingBelt Installation To Adjust Brake See FigTo Replace Mower Blade Drive Belt See Fig To Replace Motion Drive Belt See FigTransaxle Motion Control Lever Neutral Adjustment See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERReplacing Battery See Figs To Start Engine with a Weak Battery See FigTo Replace Headlight Bulb To Attach Jumper CablesInterlocks and Relays To Adjust CarburetorTo Replace Fuse Other StorageFuel System Engine OILTroubleshooting Points OFF Tractor - Model Number PPR20H42STB SchematicElectrical KEY Part Description Chassis Screw Hex Wshd 8-18 x 7/8 Drive KEY Steering Assembly KEY Part NO. NO. Description Seat Assembly Wheels and Tires DecalsOptional Equipment EngineSpark Arrester 170771 Control, Throttle Mower Deck Wheel, Gauge Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

183255 specifications

The Poulan 183255 is a versatile and robust tool designed for homeowners and professionals alike, particularly suited for tackling lawn maintenance and light landscaping tasks. Known for its reliability and efficiency, the Poulan 183255 is equipped with an array of features that enhance its usability and performance.

One of its standout features is the powerful gas engine that ensures robust cutting performance. With a displacement of 25cc, the engine delivers impressive torque while maintaining fuel efficiency. The lightweight design of the unit makes it easy to handle, reducing user fatigue during prolonged use. One of the key characteristics of the Poulan 183255 is its ergonomic design, which includes a comfortable grip and adjustable handle, allowing for extended operation without discomfort.

The cutting head of the Poulan 183255 is designed for versatility, accommodating different types of attachments. This feature enables users to switch between trimming and edging tasks seamlessly, making it an ideal choice for maintaining a well-groomed lawn. The trimmer line is easy to replace, ensuring minimal downtime and allowing users to get back to work quickly.

Another notable technology in the Poulan 183255 is the Easy Start System, which reduces the effort required to start the machine. This system minimizes the time spent on starting and maximizes efficiency, allowing users to get straight to their trimming tasks without hassle. Additionally, the unit is built to minimize vibration, providing a smoother experience during operation and contributing to overall user comfort.

The Poulan 183255 also boasts a durable construction, making it suitable for various environments, from residential lawns to more challenging terrains. Its rugged design ensures longevity, even when faced with demanding tasks. Furthermore, maintenance is straightforward, with easily accessible parts that allow for quick repairs and service.

In summary, the Poulan 183255 is a powerful, versatile, and user-friendly trimmer that is ideal for anyone looking to maintain their yard with ease. With its reliable engine, ergonomic features, and advanced technologies, it stands out as a dependable choice for effective lawn care. Whether you’re a seasoned landscaper or a weekend warrior, the Poulan 183255 provides the performance and efficiency needed to get the job done right.
Top Page Image Contents