Poulan 182705 To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig, Belt Removal

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PROD- UCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 18 and 19)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER

 

OF MOWER

TO GROUND

 

TO GROUND

“A”

GROUND LINE

“A”

FIG. 18

SUSPENSION ARM

LIFT LINK

ADJUSTMENT

NUT

FIG. 19

FRONT-TO-BACK ADJUSTMENT (See Figs. 20 and 21)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO- SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its highest position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D""D"

FIG. 20

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

 

TRUNNION

 

FRONT LINKS

FIG. 21

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 22)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instructions.

IDLER PULLEYS

MANDREL

PULLEYS

20

FIG. 22

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PR17H42STE Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Steering Wheel SeatSlope Sheet KeyAssembly Install Seat See Fig To SET UP Your Mower for Mulching Check Tire PressureCheck Deck Levelness To Convert to Bagging or DischargingOperation Know Your Tractor HOW to USE Your Tractor To Adjust Mower Cutting Height See Fig Stopping See FigTo SET Parking Brake See Fig To USE Throttle Control See FigTo Adjust Gauge Wheels See Fig To Operate on HillsTo Operate Mower See Fig To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsLubrication Chart Service DatesCustomer Responsibilities General RecommendationsTractor Engine Cleaning Engine Cooling FinsAIR Filter MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake See Fig Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PR17H42STE, Product Number 954 56Electrical KEY Part Description Chassis and Enclosures Screw Hex Wshd 8-18 x 7/8 Drive Transaxle Hydro Gear Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresEngine 170551 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Page Limited Warranty Fold Along This Dotted Line Degree Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

182705 specifications

The Poulan 182705 is a versatile and reliable chainsaw designed for both homeowners and professionals who require a robust tool for cutting firewood, trimming branches, and tackling general landscaping tasks. Its design combines power and user-friendly features, making it an excellent choice for those who need a dependable saw that can handle various tasks around the yard or property.

One of the standout features of the Poulan 182705 is its powerful engine. Equipped with a 42cc, 2-cycle gas engine, this chainsaw delivers a solid performance, ensuring that it can cut through hardwood and thick branches with ease. The engine is designed for optimal efficiency, allowing users to accomplish more work with less fuel consumption, which is both cost-effective and environmentally friendly.

Another significant highlight of the Poulan 182705 is its lightweight construction. Weighing in at about 11 pounds, this chainsaw is easy to maneuver, making it suitable for extended use without causing excessive fatigue. Its well-balanced design enhances control during operation, contributing to safer handling, especially for users who may not have extensive experience with chainsaws.

Safety is paramount in using power tools, and the Poulan 182705 is equipped with several safety features to protect the user. It includes a trigger lockout to prevent accidental starting, a chain brake that stops the chain immediately in the event of kickback, and a low-kickback chain that minimizes the risk of unwanted movement during cutting.

The chainsaw also features an automatic oiling system, which lubricates the bar and chain during operation, ensuring smooth cutting and reducing wear on the equipment. This not only extends the life of the chainsaw but also allows for maintenance-free operation for extended periods.

Additionally, the Poulan 182705 incorporates an easy-start technology that simplifies the starting process, reducing the time and effort required to get to work. This is especially beneficial for users who may struggle with traditional pull-start mechanisms.

Overall, the Poulan 182705 offers a combination of power, efficiency, and safety features that make it an ideal choice for both occasional and regular use. Whether you are a homeowner taking care of seasonal yard work or a professional in need of a reliable chainsaw, the Poulan 182705 delivers performance and ease of use that stand out in the market.
Top Page Image Contents