Poulan 182705 To Adjust Gauge Wheels See Fig, To Operate on Hills, To Operate Mower See Fig

Page 12

OPERATION

TO ADJUST GAUGE WHEELS (See Fig. 7)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•With mower in desired height of cut position, gauge wheels should be assembled so they are slightly off the ground. Install gauge wheel in appropriate hole with shoulder bolt, 3/8 washer, and 3/8-16 locknut and tighten securely.

•Repeat for opposite side installing gauge wheel in same adjustment hole.

TO OPERATE ON HILLS

CAUTION: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If slowing is necessary, move throttle control lever to slower position.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Move motion control lever to neutral (N) position.

IMPORTANT: THE MOTION CONTROL LEVER DOES NOT RETURN TO NEUTRAL (N) POSITION WHEN THE CLUTCH/BRAKE PEDAL IS DEPRESSED.

3/8-16

LOCKNUT

GUAGE WHEEL

 

MOUNTING

 

BRACKET

SHOULDER

3/8 WASHER

BOLT

 

GAUGE WHEEL

 

FIG. 7

TO OPERATE MOWER (See Fig. 8)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield in place.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Slowly move motion control lever to slowest setting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 5 and 9)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attach- ment lift control.

•Pull freewheel control out and down into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

"ENGAGED" POSITION

 

ATTACHMENT

 

LIFT LEVER

 

HIGH POSITION

 

LOW

 

POSITION

ATTACHMENT

DEFLECTOR

CLUTCH LEVER

SHIELD

"DISENGAGED"

 

POSITION

 

FIG. 8

FIG. 9

TOWING CARTS AND OTHER ATTACHMENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents PR17H42STE Safety Rules IV. ServiceGeneral Operation II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Steering Wheel SeatSlope Sheet KeyAssembly Install Seat See Fig To SET UP Your Mower for Mulching Check Tire PressureCheck Deck Levelness To Convert to Bagging or DischargingOperation Know Your Tractor HOW to USE Your Tractor To Adjust Mower Cutting Height See Fig Stopping See FigTo SET Parking Brake See Fig To USE Throttle Control See FigTo Adjust Gauge Wheels See Fig To Operate on HillsTo Operate Mower See Fig To Transport See FigsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsLubrication Chart Service DatesCustomer Responsibilities General RecommendationsTractor Engine Cleaning Engine Cooling FinsAIR Filter MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake See Fig Transmission REMOVAL/REPLACEMENTTransaxle Motion Control Lever Neutral ADJUSTMENTSee Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysStorage OtherFuel System Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PR17H42STE, Product Number 954 56Electrical KEY Part Description Chassis and Enclosures Screw Hex Wshd 8-18 x 7/8 Drive Transaxle Hydro Gear Steering Assembly KEY Part NO. NO. Description Seat Assembly Decals Wheels and TiresEngine 170551 Control Th/ch Flag Mower Deck Repair Parts Mower Lift 159460 Wire Asm Inner/Sprg W/plunger LT Page Page Limited Warranty Fold Along This Dotted Line Degree Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

182705 specifications

The Poulan 182705 is a versatile and reliable chainsaw designed for both homeowners and professionals who require a robust tool for cutting firewood, trimming branches, and tackling general landscaping tasks. Its design combines power and user-friendly features, making it an excellent choice for those who need a dependable saw that can handle various tasks around the yard or property.

One of the standout features of the Poulan 182705 is its powerful engine. Equipped with a 42cc, 2-cycle gas engine, this chainsaw delivers a solid performance, ensuring that it can cut through hardwood and thick branches with ease. The engine is designed for optimal efficiency, allowing users to accomplish more work with less fuel consumption, which is both cost-effective and environmentally friendly.

Another significant highlight of the Poulan 182705 is its lightweight construction. Weighing in at about 11 pounds, this chainsaw is easy to maneuver, making it suitable for extended use without causing excessive fatigue. Its well-balanced design enhances control during operation, contributing to safer handling, especially for users who may not have extensive experience with chainsaws.

Safety is paramount in using power tools, and the Poulan 182705 is equipped with several safety features to protect the user. It includes a trigger lockout to prevent accidental starting, a chain brake that stops the chain immediately in the event of kickback, and a low-kickback chain that minimizes the risk of unwanted movement during cutting.

The chainsaw also features an automatic oiling system, which lubricates the bar and chain during operation, ensuring smooth cutting and reducing wear on the equipment. This not only extends the life of the chainsaw but also allows for maintenance-free operation for extended periods.

Additionally, the Poulan 182705 incorporates an easy-start technology that simplifies the starting process, reducing the time and effort required to get to work. This is especially beneficial for users who may struggle with traditional pull-start mechanisms.

Overall, the Poulan 182705 offers a combination of power, efficiency, and safety features that make it an ideal choice for both occasional and regular use. Whether you are a homeowner taking care of seasonal yard work or a professional in need of a reliable chainsaw, the Poulan 182705 delivers performance and ease of use that stand out in the market.
Top Page Image Contents