Poulan 183046 owner manual Tractor

Page 16

CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performing any mainte- nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 11)

•Raise mower to highest position to allow access to blades.

•Remove hex bolt, lock washer and flat washer securing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble hex bolt, lock washer and flat washer in exact order as shown.

•Tighten bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

TRAILING

 

MANDREL

EDGE UP

BLADE

ASSEMBLY

 

 

 

CENTER

 

 

HOLE

 

FLAT WASHER

 

 

LOCK WASHER

 

STAR

 

 

HEX BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 11

TO SHARPEN BLADE (See Fig. 12)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT

BLADE

 

OR PIN

 

FIG. 12

BATTERY

Your tractor has a battery charging system which is suffi- cient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not

16necessary.

Page 15 Page 17
Image 16
Page 15 Page 17
Contents PR1742STF IV. Service Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesContents of Hardware Pack Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CAR- TONInstall Seat See Fig To SET UP Your Mower for Mulching To Convert to Bagging or DISCHARG- INGCheck Tire Pressure Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To TransportBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigMowing Tips Mulching Mowing TipsLubrication Chart Customer ResponsibilitiesGeneral Recommendations Before Each USETractor Clean AIR Screen EngineBelts Transaxle CoolingCleaning MufflerSpark Plugs Engine OIL FilterTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Adjust Steering Wheel Alignment To Start Engine with a Weak Battery See FigReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Replace Headlight BulbInterlocks and Relays To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points OFF Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

183046 specifications

The Poulan 183046 is a powerful and versatile chainsaw, designed to tackle a wide range of cutting tasks with ease. One of its standout features is the robust 18-inch cutting bar, allowing users to efficiently fell medium to large trees, prune branches, and handle firewood cutting. The length of the bar strikes a perfect balance between maneuverability and cutting capability, making it ideal for both novice users and seasoned professionals.

Powered by a reliable 42cc two-stroke engine, the Poulan 183046 delivers impressive performance. Its high power-to-weight ratio ensures that users can work for extended periods without experiencing fatigue. Furthermore, the engine is designed for easy starting, thanks to the chain brake and the choke lever, which help in reducing the effort required to initiate the engine.

One of the key technologies that set the Poulan 183046 apart is its advanced air filtration system. This system helps to prolong the life of the engine by keeping harmful debris and particles from entering and causing damage. Coupled with a tool-less fuel and oil cap, the chainsaw is designed for user convenience, making it simple to refuel and maintain.

Safety features are paramount in chainsaw design, and the Poulan 183046 does not disappoint. It comes equipped with a chain brake, which activates in the event of kickback, significantly reducing the risk of injury. Additionally, its ergonomic design includes a comfortable grip and anti-vibration technology, allowing users to maintain control even during prolonged use.

The Poulan 183046 is also engineered for durability, featuring high-quality materials that can withstand harsh outdoor conditions. Its design not only focuses on performance but also on providing a lasting tool that homeowners and professionals alike can rely on for their cutting needs.

Overall, the Poulan 183046 combines power, safety, and ease of use, appealing to a wide range of users from casual homeowners to dedicated landscapers. Its blend of advanced technologies and thoughtful design ensures that it remains a top choice in the competitive chainsaw market. Whether you're looking to tackle a tough job in your backyard or manage landscaping projects, the Poulan 183046 is engineered to get the job done efficiently and effectively.
Top Page Image Contents