Poulan 183046 owner manual To Adjust Steering Wheel Alignment, Front Wheel TOE-IN/CAMBER

Page 22

SERVICE AND ADJUSTMENTS

TO ADJUST STEERING WHEEL ALIGNMENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe- in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 27)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE

COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 27

TO START ENGINE WITH A WEAK BATTERY (See Fig. 28)

CAUTION: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the CUSTOMER RESPON- SIBILITIES section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT NEGATIVE GROUNDED SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT NEGATIVE GROUNDED SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect each end of the RED cable to the POSITIVE (+) terminal of each battery, taking care not to short against chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal of fully charged battery.

•Connect the other end of the BLACK cable to a good CHASSIS GROUND, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

POSITIVE TERMINAL

NEGATIVE TERMINAL

CHASSIS

 

 

CABLES

 

CHARGED

POSITIVE

BATTERY

TERMINAL

NEGATIVE

 

 

TERMINAL

FIG. 28

REPLACING BATTERY (See Figs. 29 and 30)

CAUTION: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acciden- tal grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PR1742STF General Operation IV. ServiceSafe Operation Practices for Ride-On Mowers II. Slope OperationTable of Contents Product Specifications Customer ResponsibilitiesContents of Hardware Pack HOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CAR- TONInstall Seat See Fig Check Tire Pressure To SET UP Your Mower for MulchingTo Convert to Bagging or DISCHARG- ING Check Deck LevelnessOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Mulching Mowing TipsGeneral Recommendations Lubrication ChartCustomer Responsibilities Before Each USETractor Belts Clean AIR ScreenEngine Transaxle CoolingSpark Plugs CleaningMuffler Engine OIL FilterTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTransaxle Gear Shift Lever Neutral Adjustment See Fig To Adjust Brake See FigTo Replace Motion Drive Belt See Fig Replacing Battery See Figs To Adjust Steering Wheel AlignmentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points OFF Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

183046 specifications

The Poulan 183046 is a powerful and versatile chainsaw, designed to tackle a wide range of cutting tasks with ease. One of its standout features is the robust 18-inch cutting bar, allowing users to efficiently fell medium to large trees, prune branches, and handle firewood cutting. The length of the bar strikes a perfect balance between maneuverability and cutting capability, making it ideal for both novice users and seasoned professionals.

Powered by a reliable 42cc two-stroke engine, the Poulan 183046 delivers impressive performance. Its high power-to-weight ratio ensures that users can work for extended periods without experiencing fatigue. Furthermore, the engine is designed for easy starting, thanks to the chain brake and the choke lever, which help in reducing the effort required to initiate the engine.

One of the key technologies that set the Poulan 183046 apart is its advanced air filtration system. This system helps to prolong the life of the engine by keeping harmful debris and particles from entering and causing damage. Coupled with a tool-less fuel and oil cap, the chainsaw is designed for user convenience, making it simple to refuel and maintain.

Safety features are paramount in chainsaw design, and the Poulan 183046 does not disappoint. It comes equipped with a chain brake, which activates in the event of kickback, significantly reducing the risk of injury. Additionally, its ergonomic design includes a comfortable grip and anti-vibration technology, allowing users to maintain control even during prolonged use.

The Poulan 183046 is also engineered for durability, featuring high-quality materials that can withstand harsh outdoor conditions. Its design not only focuses on performance but also on providing a lasting tool that homeowners and professionals alike can rely on for their cutting needs.

Overall, the Poulan 183046 combines power, safety, and ease of use, appealing to a wide range of users from casual homeowners to dedicated landscapers. Its blend of advanced technologies and thoughtful design ensures that it remains a top choice in the competitive chainsaw market. Whether you're looking to tackle a tough job in your backyard or manage landscaping projects, the Poulan 183046 is engineered to get the job done efficiently and effectively.
Top Page Image Contents