Poulan 182946 manual Tractor, Brake Operation, Tires, Operator Presence System, Blade Care

Page 15

CUSTOMER RESPONSIBILITIES

TRACTOR

Always observe safety rules when performing any mainte- nance.

BRAKE OPERATION

If tractor requires more than six (6) feet stopping distance at high speed in highest gear, then brake must be adjusted. (See “TO ADJUST BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See “PRODUCT SPECIFICATIONS” section of this manual).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM

Be sure operator presence and interlock systems are work- ing properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the clutch/brake pedal is fully depressed and attachement clutch control is in the disengaged position.

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

BLADE CARE

For best results mower blades must be kept sharp. Replace bent or damaged blades.

BLADE REMOVAL (See Fig. 8)

•Raise mower to highest position to allow access to blades.

•Remove blade bolt, lock washer and flat washer secur- ing blade.

•Install new or resharpened blade with trailing edge up towards deck as shown.

IMPORTANT: TO ENSURE PROPER ASSEMBLY, CENTER HOLE IN BLADE MUST ALIGN WITH STAR ON MANDREL ASSEMBLY.

•Reassemble blade bolt, lock washer and flat washer in exact order as shown.

•Tighten blade bolt securely (27-35 Ft. Lbs. torque).

IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED.

MANDREL

TRAILINGASSEMBLY EDGE UP

CENTER

HOLE

LOCK WASHER

STAR

FLAT WASHER

BLADE

 

BLADE BOLT (GRADE 8)*

*A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD.

FIG. 8

TO SHARPEN BLADE (See Fig. 9)

NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced.

Care should be taken to keep the blade balanced. An unbalanced blade will cause excessive vibration and even- tual damage to mower and engine.

•The blade can be sharpened with a file or on a grinding wheel. Do not attempt to sharpen while on the mower.

•To check blade balance, you will need a 5/8" diameter steel bolt, pin, or a cone balancer. (When using a cone balancer, follow the instructions supplied with balancer.)

NOTE: Do not use a nail for balancing blade. The lobes of the center hole may appear to be centered, but are not.

•Slide blade on to an unthreaded portion of the steel bolt or pin and hold the bolt or pin parallel with the ground. If blade is balanced, it should remain in a horizontal position. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced.

CENTER HOLE

5/8" BOLT

BLADE

OR PIN

 

FIG. 9

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model NO. PO1538B II. Slope Operation Safety RulesIV. Service General OperationSafe Operation Practices for Ride-On Mowers Safety RulesTable of Contents Steering Wheel Seat Unassembled PartsTo Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorLower seat into operating position and sit on seat Install Seat See FigCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Check Engine OIL Level Before Starting the EngineTo Operate on Hills To Transport Towing Carts and Other ATTACH- MentsTo Start Engine See Fig Mowing TipsGeneral Recommendations Lubrication ChartService Dates Customer ResponsibilitiesOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsEngine Cooling Fins See Fig Clean AIR ScreenTo Service PRE-CLEANER To Service CartridgeIN-LINE Fuel Filter See Fig CleaningMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Brake See FigTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Remove CABLES, Reverse Order To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Attach Jumper CablesTo Replace Fuse To Adjust CarburetorTo Replace Headlight Bulb Interlocks and RelaysEngine OIL StorageOther Fuel SystemTroubleshooting Points OFF Tractor - Model Number PO1538B, Product Number 954 56 SchematicElectrical KEY Part Description Chassis Repair Parts Drive KEY Part NO. NO. Description Steering 133741X428 Wheel Steering 175131 Axle Asm Optional Equipment 170551 Control Th/ch Flag Seat LBD48 DecalsWheels & Tires LSB42Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

182946 specifications

The Poulan 182946 is a power-packed chainsaw designed for both amateur woodworkers and professional landscapers alike. Built with robust features and cutting-edge technologies, this chainsaw offers an impressive balance of performance, efficiency, and ease of use, making it an ideal choice for a wide range of cutting tasks.

One of the most notable features of the Poulan 182946 is its powerful engine, which delivers high speed and torque necessary for cutting through tough materials. The chainsaw is equipped with a 42cc engine that provides an excellent blend of power and lightweight design, allowing users to tackle tasks with less fatigue. The inclusion of an automatic oiling system ensures that the chain is always properly lubricated for smooth operation, thereby extending the life of the chainsaw and maintaining optimal cutting performance.

The cutting capacity of the Poulan 182946 is further enhanced by a 16-inch bar and chain. This size strikes an ideal balance for residential projects like trimming branches, cutting firewood, or clearing small trees, without making the tool cumbersome or difficult to handle. Its low kickback design offers added safety, which is essential for beginners and those less experienced with power tools.

In terms of technological features, the Poulan 182946 incorporates a tool-less chain tensioning system. This allows users to make quick adjustments to the chain without the use of additional tools, significantly speeding up the setup process. The easy-start system minimizes the effort required to start the engine, ensuring that users can get to work without unwanted delays.

Furthermore, the chainsaw is designed with user comfort in mind. Its ergonomic handle allows for a secure grip, reducing vibration and enhancing control during operation. The compact design also contributes to a balanced feel in hand, facilitating prolonged use without discomfort.

The Poulan 182946 is not just a powerful tool; it is a reliable partner for all cutting tasks. Whether you are a seasoned professional or a DIY enthusiast, this chainsaw promises to deliver exceptional performance, reliability, and user-friendly features that enhance your cutting experience. Ultimately, the Poulan 182946 stands as a testament to Poulan's commitment to creating quality outdoor power equipment that meets the needs of today's users.
Top Page Image Contents