Poulan 182946 manual Tools Required for Assembly, To Remove Tractor from Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(2)

1/2" wrenches

Pliers

(1)

9/16" wrench

Tire pressure gauge

Utility knife

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut, from top to bottom, along lines on all four corners of carton, and lay panels flat.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft. Align mounting holes in extension and lower shafts and install 1/4 hex bolt and locknut. Tighten securely.

 

INSERT

 

1/2 HEX NUT

 

LARGE FLAT

 

WASHER

STEERING

STEERING

BOOT

WHEEL

 

 

TABS

ADAPTER

 

 

EXTENSION SHAFT

 

1/4 HEX BOLT

1/4 LOCKNUT

 

LOWER

TAB

SLOTS

STEERING

 

SHAFT

 

IMPORTANT: TIGHTEN BOLT AND NUT SECURELY TO

FIG. 1

10-12 FT. LBS TORQUE.

 

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 1/2 hex nut and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

HOW TO SET UP YOUR TRACTOR

CHECK BATTERY (See Fig. 2)

•Lift seat pan to raised position.

•If this battery is put into service after month and year indicated on label (label located between terminals) charge battery for minimum of one hour at 6-10 amps. (See “BATTERY” in the Customer Responsibilities sec- tion of this manual for charging instructions).

SEAT PAN

LABEL

FIG. 2

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Model NO. PO1538B General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Steering Wheel SeatHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Lower seat into operating position and sit on seatCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Towing Carts and Other ATTACH- Ments Before Starting the EngineTo Operate on Hills To Transport Check Engine OIL LevelMowing Tips To Start Engine See FigCustomer Responsibilities Lubrication ChartService Dates General RecommendationsTires TractorBrake Operation Operator Presence SystemBelts BatteryEngine Transaxle CoolingTo Service Cartridge Clean AIR ScreenTo Service PRE-CLEANER Engine Cooling Fins See FigSpark Plugs CleaningMuffler IN-LINE Fuel Filter See FigService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove CABLES, Reverse OrderInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PO1538B, Product Number 954 56Electrical KEY Part Description Chassis Repair Parts Drive KEY Part NO. NO. Description Steering 133741X428 Wheel Steering 175131 Axle Asm Optional Equipment 170551 Control Th/ch Flag Seat LSB42 DecalsWheels & Tires LBD48Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

182946 specifications

The Poulan 182946 is a power-packed chainsaw designed for both amateur woodworkers and professional landscapers alike. Built with robust features and cutting-edge technologies, this chainsaw offers an impressive balance of performance, efficiency, and ease of use, making it an ideal choice for a wide range of cutting tasks.

One of the most notable features of the Poulan 182946 is its powerful engine, which delivers high speed and torque necessary for cutting through tough materials. The chainsaw is equipped with a 42cc engine that provides an excellent blend of power and lightweight design, allowing users to tackle tasks with less fatigue. The inclusion of an automatic oiling system ensures that the chain is always properly lubricated for smooth operation, thereby extending the life of the chainsaw and maintaining optimal cutting performance.

The cutting capacity of the Poulan 182946 is further enhanced by a 16-inch bar and chain. This size strikes an ideal balance for residential projects like trimming branches, cutting firewood, or clearing small trees, without making the tool cumbersome or difficult to handle. Its low kickback design offers added safety, which is essential for beginners and those less experienced with power tools.

In terms of technological features, the Poulan 182946 incorporates a tool-less chain tensioning system. This allows users to make quick adjustments to the chain without the use of additional tools, significantly speeding up the setup process. The easy-start system minimizes the effort required to start the engine, ensuring that users can get to work without unwanted delays.

Furthermore, the chainsaw is designed with user comfort in mind. Its ergonomic handle allows for a secure grip, reducing vibration and enhancing control during operation. The compact design also contributes to a balanced feel in hand, facilitating prolonged use without discomfort.

The Poulan 182946 is not just a powerful tool; it is a reliable partner for all cutting tasks. Whether you are a seasoned professional or a DIY enthusiast, this chainsaw promises to deliver exceptional performance, reliability, and user-friendly features that enhance your cutting experience. Ultimately, the Poulan 182946 stands as a testament to Poulan's commitment to creating quality outdoor power equipment that meets the needs of today's users.
Top Page Image Contents