Poulan 182946 manual To Start Engine with a Weak Battery See Fig, Replacing Battery See Figs

Page 22

SERVICE AND ADJUSTMENTS

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 23

TO START ENGINE WITH A WEAK BATTERY (See Fig. 24)

WARNING: Lead-acid batteries generate explosive gases. Keep sparks, flame and smoking materials away from bat- teries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the CUSTOMER RESPON- SIBILITIES section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE (+) terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

REPLACING BATTERY (See Figs. 25 and 26)

CAUTION: Do not short battery terminals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands, rings, etc.

Positive terminal must be connected first to prevent sparking from acciden- tal grounding.

•Lift seat pan to raised position.

•Disconnect BLACK battery cable first then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) terminal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

FIG. 25

KEPS

TERMINALNUT

COVER

HEX

BOLT

POSITIVE

NEGATIVE

(RED) CABLE

(BLACK) CABLE

 

FIG. 26

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

FIG. 24

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model NO. PO1538B General Operation Safety RulesIV. Service II. Slope OperationSafety Rules Safe Operation Practices for Ride-On MowersTable of Contents Unassembled Parts Steering Wheel SeatHOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Lower seat into operating position and sit on seatCheck for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Towing Carts and Other ATTACH- Ments Before Starting the EngineTo Operate on Hills To Transport Check Engine OIL LevelMowing Tips To Start Engine See FigCustomer Responsibilities Lubrication ChartService Dates General RecommendationsTires TractorBrake Operation Operator Presence SystemBelts BatteryEngine Transaxle CoolingTo Service Cartridge Clean AIR ScreenTo Service PRE-CLEANER Engine Cooling Fins See FigSpark Plugs CleaningMuffler IN-LINE Fuel Filter See FigTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Adjust Brake See FigTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Attach Jumper Cables To Start Engine with a Weak Battery See FigReplacing Battery See Figs To Remove CABLES, Reverse OrderInterlocks and Relays To Adjust CarburetorTo Replace Headlight Bulb To Replace FuseFuel System StorageOther Engine OILTroubleshooting Points OFF Schematic Tractor - Model Number PO1538B, Product Number 954 56Electrical KEY Part Description Chassis Repair Parts Drive KEY Part NO. NO. Description Steering 133741X428 Wheel Steering 175131 Axle Asm Optional Equipment 170551 Control Th/ch Flag Seat LSB42 DecalsWheels & Tires LBD48Mower Lift 159460 Wire Asm Inner/Sprg w/plunger Mower Deck Repair Parts Service Notes Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAX

182946 specifications

The Poulan 182946 is a power-packed chainsaw designed for both amateur woodworkers and professional landscapers alike. Built with robust features and cutting-edge technologies, this chainsaw offers an impressive balance of performance, efficiency, and ease of use, making it an ideal choice for a wide range of cutting tasks.

One of the most notable features of the Poulan 182946 is its powerful engine, which delivers high speed and torque necessary for cutting through tough materials. The chainsaw is equipped with a 42cc engine that provides an excellent blend of power and lightweight design, allowing users to tackle tasks with less fatigue. The inclusion of an automatic oiling system ensures that the chain is always properly lubricated for smooth operation, thereby extending the life of the chainsaw and maintaining optimal cutting performance.

The cutting capacity of the Poulan 182946 is further enhanced by a 16-inch bar and chain. This size strikes an ideal balance for residential projects like trimming branches, cutting firewood, or clearing small trees, without making the tool cumbersome or difficult to handle. Its low kickback design offers added safety, which is essential for beginners and those less experienced with power tools.

In terms of technological features, the Poulan 182946 incorporates a tool-less chain tensioning system. This allows users to make quick adjustments to the chain without the use of additional tools, significantly speeding up the setup process. The easy-start system minimizes the effort required to start the engine, ensuring that users can get to work without unwanted delays.

Furthermore, the chainsaw is designed with user comfort in mind. Its ergonomic handle allows for a secure grip, reducing vibration and enhancing control during operation. The compact design also contributes to a balanced feel in hand, facilitating prolonged use without discomfort.

The Poulan 182946 is not just a powerful tool; it is a reliable partner for all cutting tasks. Whether you are a seasoned professional or a DIY enthusiast, this chainsaw promises to deliver exceptional performance, reliability, and user-friendly features that enhance your cutting experience. Ultimately, the Poulan 182946 stands as a testament to Poulan's commitment to creating quality outdoor power equipment that meets the needs of today's users.
Top Page Image Contents