Poulan 191713 manual To Level Mower Housing, FRONT-TO-BACK Adjustment See Figs

Page 19

SERVICE AND ADJUSTMENTS

•Push clutch cable housing guide into bracket, slide col- lar onto guide and secure with large retainer spring.

•Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

•Install belt onto engine pulley.

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 14 and 15)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE OF

 

BOTTOM EDGE

MOWER

00598

OF MOWER

TO GROUND

 

TO GROUND

“A”“A”

GROUND LINE

FIG. 14

SUSPENSION ARM

01553

LIFT LINK

ADJUSTMENT

NUT

FIG. 15

FRONT-TO-BACK ADJUSTMENT (See Figs. 16 and 17)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

01268

"D"

"D"

FIG. 16

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

01267

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 17

19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Model NO. PO15538C II. Slope Operation Safety RulesIV. Service General OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsBefore Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig HOW to SET UP Your TractorCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsBefore Each USE MaintenanceLubrication Chart General RecommendationsOperator Presence System TractorBrake Operation TiresTransaxle Cooling BatteryEngine BeltsMuffler CleaningClean AIR Screen AIR FilterTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigFront Wheel TOE-IN/CAMBER To Start Engine with a Weak Battery See FigTo Adjust Steering Wheel ALIGN- Ment To Replace Motion Drive Belt See FigTo Replace Fuse Replacing Battery See FigsTo Replace Headlight Bulb Interlocks and RelaysTo Adjust Carburetor To Remove Hood and Grill Assembly See FigTo Adjust Throttle Control Cable To Adjust Choke ControlEngine OIL StorageOther Fuel SystemTroubleshooting Points With attachment clutch Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

191713 specifications

The Poulan 191713 is a powerful and versatile chainsaw designed for both homeowners and professionals who require a reliable cutting tool for various applications. Known for its robust performance and user-friendly features, it has garnered a reputation for dependability in the realms of tree trimming, firewood cutting, and outdoor maintenance.

One of the standout features of the Poulan 191713 is its efficient two-cycle engine, delivering exceptional power while maintaining a lightweight profile. This allows users to handle the chainsaw comfortably for extended periods without experiencing fatigue. The engine is designed for easy starting, thanks to the Smart Start technology, which reduces the amount of effort needed to pull the starter cord. This aspect is particularly beneficial for novice users or those who may not have much experience with chainsaws.

The 191713 incorporates a 16-inch bar and chain, providing a perfect balance between cutting capacity and maneuverability. This size is ideal for tackling medium-sized logs and branches with ease, making it a versatile choice for various cutting tasks. The chainsaw also features an automatic oiling system, ensuring that the chain is consistently lubricated during operation. This not only enhances cutting efficiency but also prolongs the life of the chain and bar.

In terms of safety, the Poulan 191713 is equipped with essential features such as a chain brake, which helps prevent accidents by stopping the chain quickly in case of kickback. Additionally, the chainsaw’s ergonomic handle provides a secure and comfortable grip, further promoting safe operation. The lightweight design and well-placed controls also contribute to user comfort, making it easier to navigate around obstacles during cutting tasks.

Maintenance is simplified with the Poulan 191713, as it includes easily accessible air filters and spark plugs. This facilitates quick cleaning and replacement, ensuring that the chainsaw remains in optimal working condition.

In summary, the Poulan 191713 is a well-engineered chainsaw that blends power, ease of use, and safety features. With its reliable performance and practical technologies, it stands out as an excellent tool for anyone looking to manage their outdoor space efficiently. Whether you are a seasoned professional or a weekend warrior, the Poulan 191713 is designed to meet your cutting needs effectively.
Top Page Image Contents