Poulan 191713 manual To Replace Motion Drive Belt See Fig, Front Wheel TOE-IN/CAMBER

Page 21

SERVICE AND ADJUSTMENTS

TO REPLACE MOTION DRIVE BELT (See Fig. 20)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from around engine pulley.

•Pull belt slack toward rear of tractor. Remove belt upwards from transaxle pulley by deflecting belt keep- ers.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down between transaxle belt keepers and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor. If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 21)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING RING

AXLE COVER

ENGINE

PULLEY

CLUTCHING

IDLER

CENTER SPAN KEEPER

00811

STATIONARY IDLER

TRANSAXLE PULLEY

SQUARE KEY

(REAR WHEEL ONLY)

FIG. 21

TO START ENGINE WITH A WEAK BATTERY (See Fig. 22)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow

FIG. 20

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Model NO. PO15538C IV. Service Safety RulesGeneral Operation II. Slope OperationSafety Rules Table of Contents Steering Wheel Seat Unassembled PartsTools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidHOW to SET UP Your Tractor Install Seat See FigCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine See Fig Mowing TipsLubrication Chart MaintenanceGeneral Recommendations Before Each USEBrake Operation TractorTires Operator Presence SystemEngine BatteryBelts Transaxle CoolingClean AIR Screen CleaningAIR Filter MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig FRONT-TO-BACK Adjustment See Figs To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak Battery See FigTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb Replacing Battery See FigsInterlocks and Relays To Replace FuseTo Adjust Throttle Control Cable To Remove Hood and Grill Assembly See FigTo Adjust Choke Control To Adjust CarburetorOther StorageFuel System Engine OILTroubleshooting Points With attachment clutch Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe Operation

191713 specifications

The Poulan 191713 is a powerful and versatile chainsaw designed for both homeowners and professionals who require a reliable cutting tool for various applications. Known for its robust performance and user-friendly features, it has garnered a reputation for dependability in the realms of tree trimming, firewood cutting, and outdoor maintenance.

One of the standout features of the Poulan 191713 is its efficient two-cycle engine, delivering exceptional power while maintaining a lightweight profile. This allows users to handle the chainsaw comfortably for extended periods without experiencing fatigue. The engine is designed for easy starting, thanks to the Smart Start technology, which reduces the amount of effort needed to pull the starter cord. This aspect is particularly beneficial for novice users or those who may not have much experience with chainsaws.

The 191713 incorporates a 16-inch bar and chain, providing a perfect balance between cutting capacity and maneuverability. This size is ideal for tackling medium-sized logs and branches with ease, making it a versatile choice for various cutting tasks. The chainsaw also features an automatic oiling system, ensuring that the chain is consistently lubricated during operation. This not only enhances cutting efficiency but also prolongs the life of the chain and bar.

In terms of safety, the Poulan 191713 is equipped with essential features such as a chain brake, which helps prevent accidents by stopping the chain quickly in case of kickback. Additionally, the chainsaw’s ergonomic handle provides a secure and comfortable grip, further promoting safe operation. The lightweight design and well-placed controls also contribute to user comfort, making it easier to navigate around obstacles during cutting tasks.

Maintenance is simplified with the Poulan 191713, as it includes easily accessible air filters and spark plugs. This facilitates quick cleaning and replacement, ensuring that the chainsaw remains in optimal working condition.

In summary, the Poulan 191713 is a well-engineered chainsaw that blends power, ease of use, and safety features. With its reliable performance and practical technologies, it stands out as an excellent tool for anyone looking to manage their outdoor space efficiently. Whether you are a seasoned professional or a weekend warrior, the Poulan 191713 is designed to meet your cutting needs effectively.
Top Page Image Contents