Poulan 271150 manual To Remove Mower, To Install Mower

Page 20

SERVICE AND ADJUSTMENTS

WARNING: TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SER- VICE OR ADJUSTMENTS:

1.Depress clutch/brake pedal fully and set parking brake.

2.Place gearshift lever in neutral (N) position.

3.Place attachment clutch in “DISENGAGED” position.

4.Turn ignition key to “STOP” and remove key.

5.Make sure the blades and all moving parts have completely stopped.

6.Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER

Mower will be easier to remove from the right side of tractor.

1.Place attachment clutch in “DISEN- GAGED” position.

2.Move attachment lift lever forward to lower mower to its lowest position.

3.Roll belt off engine pulley.

4.Remove small retainer spring, and remove clutch spring off pulley bolt.

5.Remove large retainer spring, slide collar off and push housing guide out of bracket.

6.Disconnect anti-sway bar from chassis bracket by removing retainer spring.

7.Disconnect suspension arms from rear deck brackets by removing retainer springs.

8.Disconnect front links from deck by removing retainer springs.

9.Raise lift lever to raise suspension arms. Slide mower out from under trac- tor.

IMPORTANT: If an attachment other than the mower deck is to be mounted on the tractor, remove the front links and hook the clutch spring Into square hole in frame.

TO INSTALL MOWER

1.Raise attachment lift lever to its highest position.

2.Slide mower under tractor with deflec- tor shield to right side of tractor.

3.Lower lift lever to its lowest position.

4.Connect front links to mower deck and secure with retainer springs.

5.Connect suspension arms to rear deck brackets and secure with retainer springs.

6.Connect anti-sway bar to chassis bracket and secure with retainer spring.

7.Push clutch cable housing guide into bracket, slide collar onto guide and secure with large retainer spring.

8.Place flat washer and clutch spring on idler pulley bolt and secure with small retainer spring.

9.Install belt onto engine pulley.

 

Small Retainer

 

Flat Washer

Spring

 

 

 

Clutch Spring

Suspension

Square Hole

Small Retainer

Arms

 

 

Engine

Clutch Spring

 

Spring

 

Pulley

Retainer

 

 

Spring

 

Front Link

Anti-Sway

 

Retainer Springs

Bar

 

(Both Sides)

Collar

 

 

Housing

Guide

Large Retainer

Deflector Shield

Spring

Bracket

 

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Model no Table of Contents IV. Service III. ChildrenWash hands after handling Product Specifications Customer ResponsibilitiesAPI-SF-SJ U1RUnassembled Parts Tools Required for Assembly To Remove Tractor from CartonBefore Removing Tractor from Skid Unpack CartonCheck Battery HOW to SET UP Your TractorInstall Seat Check Tire Pressure Check for Proper Position of ALL BeltsCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Before Starting the Engine To Start Engine ADD GasolineMowing Tips General Recommendations Lubrication Chart Before Each USETractor Engine AIR FilterCleaning Engine Cooling FinsMuffler Spark PlugsTo Install Mower To Remove MowerTo Level Mower Housing SIDE-TO-SIDE AdjustmentTo Replace Mower Blade Drive Belt Belt RemovalBelt Installation To Check and Adjust BrakeTo Adjust Brake To Check BrakeTo Adjust Steering Wheel ALIGN- Ment To Start Engine with a Weak BatteryReplacing Battery Front Wheel TOE-IN/CAMBERTo Adjust Carburetor Battery OtherEngine OIL CylindersTroubleshooting Chart Problem Cause CorrectionExcessive Mower blades will Schematic Tractor -- Model NumberRepair Parts ElectricalKEY Part Description Chassis and Enclosures 174643X014 Ground Drive Bolt Carr. Sh 3/8-16 x 1-3/4 Gr Steering KEY Part NO. NO. Description Engine Optional Equipment Engine Seat Assembly Decals Wheels and TiresLift Assembly Retainer Spring Mower Deck Following blades are available Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation
Top Page Image Contents