Poulan 197418, 96012000402 manual Mowing Tips, Purge Transmission

Page 14

OPERATION

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is run-

ning.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

Place tractor safely on level surface with engine off and parking brake set.

Disengage transmission by placing freewheel control in freewheeling position (See “TO TRANSPORT” in this section of manual).

Sitting in the tractor seat, start engine. After the engine is running, move throttle control to slow position. With motion control lever in neutral (N) position, slowly dis- engage clutch/brake pedal.

Move motion control lever to full forward position and hold for five (5) seconds. Move lever to full reverse position and hold for five (5) seconds. Repeat this procedure three (3) times.

NOTE: During this procedure there will be no movement of drive wheels. The air is being removed from hydraulic drive system.

Move motion control lever to neutral (N) position. Shut- off engine and set parking brake.

Engage transmission by placing freewheel control in engaged position (See “TO TRANSPORT” in this sec- tion of manual).

Sitting in the tractor seat, start engine. After the engine is running, move throttle control to half (1/2) speed. With motion control lever in neutral (N) position, slowly disengage clutch/brake pedal.

Slowly move motion control lever forward, after the tractor moves approximately five (5) feet, slowly move motion control lever to reverse position. After the trac- tor moves approximately five (5) feet return the mo- tion control lever to the neutral (N) position. Repeat this procedure with the motion control lever three (3) times.

Your transmission is now purged and now ready for normal operation.

MOWING TIPS

Mower should be properly leveled for best mowing per- formance. See “TO LEVEL MOWER HOUSING” in the Service and Adjustments section of this manual.

The left hand side of mower should be used for trim- ming.

Drive so that clippings are discharged onto the area that has been cut. Have the cut area to the right of the machine. This will result in a more even distribution of clippings and more uniform cutting.

When mowing large areas, start by turning to the right so that clippings will discharge away from shrubs, fences, driveways, etc. After one or two rounds, mow in the opposite direction making left hand turns until finished (See Fig. 8).

FIG. 8

If grass is extremely tall, it should be mowed twice to reduce load and possible fire hazard from dried clip- pings. Make first cut relatively high; the second to the desired height.

Do not mow grass when it is wet. Wet grass will plug mower and leave undesirable clumps. Allow grass to dry before mowing.

Always operate engine at full throttle when mow- ing to assure better mowing performance and proper discharge of material. Regulate ground speed by se- lecting a low enough gear to give the mower cutting performance as well as the quality of cut desired.

When operating attachments, select a ground speed that will suit the terrain and give best performance of the attachment being used.

14

Image 14
Contents PB185H42LT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Slope Sheet Unassembled PartsSteering Wheel Seat To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS Using the Reverse Operation SystemTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips Purge TransmissionGeneral Recommendations MaintenanceLubrication Chart Before Each USETo Sharpen Blade See Fig TractorBlade Removal See Fig Engine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Adjust Brake To Check and Adjust Brake See FigTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

197418, 96012000402 specifications

The Poulan 96012000402 is a remarkable model in its class, designed to cater to the needs of both professional landscapers and DIY enthusiasts. This robust equipment offers a blend of power, efficiency, and ease of use, making it a popular choice for those tackling lawn care and garden maintenance.

One of the key features of the Poulan 96012000402 is its powerful engine, which is designed to deliver exceptional performance. With a high torque output, this machine can easily handle tough grass and dense underbrush, ensuring that users can complete their tasks quickly and effectively. The engine is also engineered for fuel efficiency, allowing for longer operation times without frequent refueling.

Another highlight of the Poulan 96012000402 is its ergonomic design. The machine comes equipped with an adjustable handlebar that provides comfort and reduces operator fatigue during extended use. Additionally, it features a lightweight construction that allows for easy maneuverability and transport, making it suitable for both large and small jobs.

The cutting deck of the Poulan 96012000402 is crafted for precision and versatility. It features adjustable cutting heights, allowing users to customize the lawn height according to their preferences. The durable blades ensure clean cuts while minimizing the risk of damage to the grass, promoting healthier growth.

In terms of technology, the Poulan 96012000402 incorporates advanced features that enhance its usability. The easy-start mechanism means that users can start the engine with minimal effort, eliminating the frustrations often associated with starting traditional engines. Furthermore, the maintenance features are user-friendly, allowing for straightforward access to critical components for cleaning and servicing.

Characteristics such as a robust build quality also set the Poulan 96012000402 apart from its competitors. Constructed from durable materials, this model is designed to withstand the rigors of regular use in various weather conditions. Its reliable performance and innovative engineering make it an excellent investment for anyone looking to maintain a pristine lawn or garden.

In summary, the Poulan 96012000402 combines power, efficiency, and comfort, making it an essential tool for gardening and landscaping. With its user-friendly features, advanced technology, and durable design, it stands out as a reliable choice for both professional landscapers and home gardeners alike. Whether tackling tough yards or maintaining a manicured lawn, this model offers the versatility and performance needed to get the job done right.