page 8 SETTINGS
page 1 | Celestia 400 |
|
Turning the ringer on and off
By default, the ringer is on.
1Press 
2Press the PLAY/PAUSE/STOP button twice The Celestia says: ‘Ring on’ or ‘Ring off’.
3Press memo or 
to switch the ringer on or off
4Press 
to save the new setting and leave Settings mode
OR press 
to leave Settings mode without saving any changes OR press PLAY/PAUSE/STOP to go back to setting the time and date
Troubleshooting
The Celestia 400 must be serviced by trained | If you cannot dial out … | |
engineers. NEVER attempt any repairs or |
| Disconnect all other instruments connected to |
adjustments yourself — you could make the |
| the same line as the Celestia 400 and see |
problem worse and invalidate the Guarantee. |
| whether you can make a call. |
Always make sure your Celestia 400 is fully |
| Disconnect the Celestia 400 from the |
plugged into the telephone line socket and the |
| telephone line and plug a telephone into the |
mains power socket. |
| socket. Try making a call. If this works, the line |
If the phone does not ring … |
| is OK. |
| If you are using a | |
|
| |
Check that the ringer volume is not set to | n n | remove it and plug a telephone directly into |
Check that the total REN value of all |
| the socket. If the call now works, the adapter |
| may be faulty. | |
equipment connected to your telephone line is |
| |
| If you think the fault may be on the exchange | |
no more than 4. Disconnect one or more |
| |
|
| |
|
|
|
CALLER ID buttons*
skip to the next record
go back to the previous record
clear records
call back the number displayed
SET button
— enter or leave Settings mode
MEMO/<</– button
— record a memo
— rewind during message playback
— decrease value in Settings mode
OGM/>>/+ button
—record an outgoing message
—
—increase value in Settings mode
*Please note that, to use these features, you need to subscribe to the BT Caller ID option, or the equivalent option from your service provider.
USER GUIDE
Model 3401
Display
see below
Microphone
ANSWER ON light This also flashes when the unit is ringing for an incoming call
DELETE/ANSWER ON button
— switch the answering machine on and off
— delete recorded messages
— leave Settings mode without changing settings
PLAY/PAUSE/STOP button
— start, pause and stop message playback
— in Settings mode, move from one setting to the next
SPEAKERPHONE button
—press while the unit is recording an incoming message, to stop recording and speak to the caller
The 
and 
buttons can also be used to adjust the speaker and ringer volumes (see page 7)
| telephones and see whether that helps. |
| line, contact the service provider (the BT | |||
|
| engineers on 151, or your cable company). | ||||
|
|
|
| |||
|
|
|
| If you still cannot identify the cause of the | ||
|
|
|
| problem, contact the Binatone Help Line. | ||
Technical details |
| Default settings |
| |||
Temperature range | Operating 0ºC to 40ºC | Time and date | 12:00 am on | |||
n |
| Storage | ||||
|
| Max. incoming message length | 3 minutes | |||
|
|
| ||||
Approvals | CTR 21 | Security code | 123 | |||
Input | 230 V AC, 50Hz, AC9 V, 200 mA | Ring count | 2 | |||
|
|
| ||||
|
|
| If the unit is disconnected from the telephone line, all | |||
Mains adapter part number XX002104D | n |
|
| |||
settings will be returned to these defaults. | ||||||
|
|
| ||||
The AC port (connected to the mains power supply) is a | Binatone Telecom plc operates a policy of continuous product | |||||
SELV port with respect to EN41003 | ||||||
|
|
| improvement, and so reserves the right to make changes to the | |||
product and functions without notice.
The display
While the Celestia 400 is idle, the display shows information as in this example:
Other information and symbols that appear on the display include:
CALL # 03 02:45 PM
00-16 -5
The time and date — 9.35 am on 13 October
There are 2 new caller ID records and 12 records altogether
There are 4 new incoming messages or memos and 15 messages/memos altogether
This appears when you press the SPEAKERPHONE button to listen and/or speak to a caller; or when you call back a number from the Caller ID memory
The bell appears when the unit is ringing for an incoming call (even if the ringer is turned off)
If you need help, call the Binatone Help Line
020 8344 8870
9.00 am to 5.00 pm, Monday to Friday
This shows the loudspeaker volume currently set
After the Celestia 400 has been connected to the line for 16 seconds, the call duration is shown here
When you call back a number from Caller ID memory, the record number is shown here
