Poulan 195506 manual Before Starting the Engine, Check Engine OIL Level, ADD Gasoline

Page 13

OPERATION

BEFORE STARTING THE ENGINE

CHECK ENGINE OIL LEVEL

The engine in your tractor has been shipped, from the factory, already filled with summer weight oil.

•Check engine oil with tractor on level ground.

•Remove oil fill cap/dipstick and wipe clean, reinsert the dipstick and screw cap tight, wait for a few seconds, remove and read oil level. If necessary, add oil until “FULL” mark on dipstick is reached. Do not overfill.

•For cold weather operation you should change oil for easier starting (See “OIL VISCOSITY CHART” in the Maintenance section of this manual).

•To change engine oil, see the Maintenance section in this manual.

ADD GASOLINE

•Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can at- tract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 5)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Sit on seat in operating position, depress clutch/brake pedal and set parking brake.

•Place gear shift lever in neutral (N) position.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to choke () position.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to“START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, move throttle control to fast position, wait a few minutes and try again. If engine still does not start, move the throttle control back to the choke ( ) position and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, move the throttle control to the fast position.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING ( 50° F and below)

•When engine starts, allow engine to run with the throttle control in the choke () position until the engine runs roughly, then move throttle control to fast position.This may require an engine warm-up period from several seconds to several minutes, depending on the tem- perature.

•The attachments can also be used during the engine warm-up period.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Always Wear EYE Protection During Operation HD1842Safe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Contents of Hardware Pack Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate on Hills To Operate Mower See FigReverse Operation System ROS To TransportCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine BatteryBelts Transaxle CoolingClean AIR Screen CleaningAIR Filter MufflerTo Install Mower See Fig Service and AdjustmentsTo Remove Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Check and Adjust Brake See FigTo Adjust Brake To Replace Motion Drive Belt See FigReplacing Battery See Figs To Adjust Steering Wheel ALIGN- MentFront Wheel TOE-IN/CAMBER To Attach Jumper CablesTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight BulbOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

195506 specifications

The Poulan 195506 is an efficient and robust gas-powered chainsaw designed for both professional and amateur users who require reliable performance for a variety of cutting tasks. This model is particularly noted for its ease of use, making it an excellent choice for homeowners looking to manage their landscaping needs or perform light logging activities.

One of the standout features of the Poulan 195506 is its powerful engine. It is equipped with a 50cc 2-cycle engine, which provides ample power for cutting through tough materials, ensuring that users can tackle everything from tree felling to firewood preparation with ease. The engine's design allows for quick starts and smooth performance, thus minimizing user fatigue during extended operation.

The chainsaw's cutting bar measures 18 inches, offering a fantastic balance between maneuverability and cutting capacity. This length is ideal for a variety of tasks, enabling users to handle both small and medium-sized trees effectively. Furthermore, the bar features a low kickback design, enhancing safety by reducing the chances of dangerous incidents during operation.

Another noteworthy characteristic of the Poulan 195506 is its automated oiling system. This feature ensures that the chain remains adequately lubricated during use, minimizing wear and tear, and prolonging the lifespan of the cutting chain. The oil reservoir is easily accessible, allowing users to refill it quickly without hassle.

In terms of user comfort, the Poulan 195506 is designed with an ergonomic handle that provides a secure grip, reducing vibration and strain during operation. This thoughtful design aspect is especially important for users who may be using the chainsaw for prolonged periods.

Additionally, the chainsaw incorporates several safety features, such as the front hand guard and a chain brake, which activate in the case of kickback, providing an extra layer of security for users. The combination of these safety features, along with its manageable weight, makes the Poulan 195506 a user-friendly choice for those at any skill level.

Overall, the Poulan 195506 is a versatile chainsaw that combines power, safety, and ease of use, making it an essential tool for anyone looking to efficiently handle their outdoor cutting tasks. Its reliable performance, attractive features, and robust construction solidify its place as a favored choice among chainsaw enthusiasts.
Top Page Image Contents