Poulan 195506 manual To Replace Headlight Bulb, Interlocks and Relays, To Replace Fuse

Page 23

SERVICE AND ADJUSTMENTS

•First connect RED battery cable to positive (+) terminal with hex bolt and keps nut as shown. Tighten securely. Slide terminal cover over terminal.

•Connect BLACK grounding cable to negative (-) ter- minal with remaining hex bolt and keps nut. Tighten securely.

SEAT PAN

 

FIG. 24

TERMINAL

KEPS NUT

COVER

 

HEX

BOLT

POSITIVE (RED) CABLE

NEGATIVE (BLACK) CABLE

FIG. 25

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

INTERLOCKS AND RELAYS

Loose or damaged wiring may cause your tractor to run poorly, stop running, or prevent it from starting.

•Check wiring. See electrical wiring diagram in the Repair Parts section.

TO REPLACE FUSE

Replace with 20 amp automotive-type plug-in fuse. The fuse holder is located behind the dash.

TO REMOVE HOOD AND GRILL ASSEMBLY (See Fig. 26)

•Raise hood.

•Unsnap headlight wire connector.

•Stand in front of tractor. Grasp hood at sides, tilt toward engine and lift off of tractor.

•To replace, reverse above procedure.

HOOD

HEADLIGHT WIRE

CONNECTOR

01536

FIG. 26

ENGINE

TO ADJUST THROTTLE CONTROL CABLE

The throttle control has been preset at the factory and adjustment should not be necessary. If adjustment is nec- essary, see engine manual.

TO ADJUST CHOKE CONTROL

The choke control has been preset at the factory and ad- justment should not be necessary. If adjustment is neces- sary, see engne manual.

TO ADJUST CARBURETOR

Your carburetor is not adjustable. If your engine does not operate properly due to suspected carburetor problems, take your tractor to an authorized service center for repair and/or adjustment.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Always Wear EYE Protection During Operation HD1842II. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationIV. Towing ServiceGeneral Service III. ChildrenTable of Contents Contents of Hardware Pack Before Removing Tractor from Skid AssemblyTools Required for Assembly To Remove Tractor from CartonCheck Battery See Fig Check Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Transport To Operate Mower See FigTo Operate on Hills Reverse Operation System ROSTo Start Engine See Fig Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Before Each USE MaintenanceLubrication Chart General RecommendationsTo Sharpen Blade See Fig TractorBlade Removal See Fig Transaxle Cooling BatteryEngine BeltsMuffler CleaningClean AIR Screen AIR FilterTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Removal To Level Mower HousingBelt Installation To Replace Mower Blade Drive Belt See FigTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust BrakeTo Attach Jumper Cables To Adjust Steering Wheel ALIGN- MentReplacing Battery See Figs Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

195506 specifications

The Poulan 195506 is an efficient and robust gas-powered chainsaw designed for both professional and amateur users who require reliable performance for a variety of cutting tasks. This model is particularly noted for its ease of use, making it an excellent choice for homeowners looking to manage their landscaping needs or perform light logging activities.

One of the standout features of the Poulan 195506 is its powerful engine. It is equipped with a 50cc 2-cycle engine, which provides ample power for cutting through tough materials, ensuring that users can tackle everything from tree felling to firewood preparation with ease. The engine's design allows for quick starts and smooth performance, thus minimizing user fatigue during extended operation.

The chainsaw's cutting bar measures 18 inches, offering a fantastic balance between maneuverability and cutting capacity. This length is ideal for a variety of tasks, enabling users to handle both small and medium-sized trees effectively. Furthermore, the bar features a low kickback design, enhancing safety by reducing the chances of dangerous incidents during operation.

Another noteworthy characteristic of the Poulan 195506 is its automated oiling system. This feature ensures that the chain remains adequately lubricated during use, minimizing wear and tear, and prolonging the lifespan of the cutting chain. The oil reservoir is easily accessible, allowing users to refill it quickly without hassle.

In terms of user comfort, the Poulan 195506 is designed with an ergonomic handle that provides a secure grip, reducing vibration and strain during operation. This thoughtful design aspect is especially important for users who may be using the chainsaw for prolonged periods.

Additionally, the chainsaw incorporates several safety features, such as the front hand guard and a chain brake, which activate in the case of kickback, providing an extra layer of security for users. The combination of these safety features, along with its manageable weight, makes the Poulan 195506 a user-friendly choice for those at any skill level.

Overall, the Poulan 195506 is a versatile chainsaw that combines power, safety, and ease of use, making it an essential tool for anyone looking to efficiently handle their outdoor cutting tasks. Its reliable performance, attractive features, and robust construction solidify its place as a favored choice among chainsaw enthusiasts.
Top Page Image Contents