Poulan 195506 manual Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1) 1/2" wrench

Utility knife

Tire pressure gauge

 

Pliers

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

INSERT

5/16 HEX BOLT

LOCK WASHER

LARGE FLAT WASHER

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•

Remove all accessible loose parts and parts cartons

 

from carton.

•

Cut along dotted lines on all four panels of carton.

STEERING WHEEL

STEERING BOOT

TABS

Remove end panels and lay side panels flat.

• Check for any additional loose parts or cartons and

remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large flat washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

ADAPTER

EXTENSION SHAFT

LOWER

STEERING

SHAFT

TAB

SLOTS

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment bolt.

•Remove adjustment bolt, lock washer and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjust- ment bolt, lockwasher and flat washer loosely. Do not tighten

Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment bolt securely.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents HD1842 Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Operate Mower See FigTo Operate on Hills To TransportADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigMowing Tips General Recommendations MaintenanceLubrication Chart Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingAIR Filter CleaningClean AIR Screen MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Adjust Brake To Check and Adjust Brake See FigTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Replace Motion Drive Belt See FigFront Wheel TOE-IN/CAMBER To Adjust Steering Wheel ALIGN- MentReplacing Battery See Figs To Attach Jumper CablesTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

195506 specifications

The Poulan 195506 is an efficient and robust gas-powered chainsaw designed for both professional and amateur users who require reliable performance for a variety of cutting tasks. This model is particularly noted for its ease of use, making it an excellent choice for homeowners looking to manage their landscaping needs or perform light logging activities.

One of the standout features of the Poulan 195506 is its powerful engine. It is equipped with a 50cc 2-cycle engine, which provides ample power for cutting through tough materials, ensuring that users can tackle everything from tree felling to firewood preparation with ease. The engine's design allows for quick starts and smooth performance, thus minimizing user fatigue during extended operation.

The chainsaw's cutting bar measures 18 inches, offering a fantastic balance between maneuverability and cutting capacity. This length is ideal for a variety of tasks, enabling users to handle both small and medium-sized trees effectively. Furthermore, the bar features a low kickback design, enhancing safety by reducing the chances of dangerous incidents during operation.

Another noteworthy characteristic of the Poulan 195506 is its automated oiling system. This feature ensures that the chain remains adequately lubricated during use, minimizing wear and tear, and prolonging the lifespan of the cutting chain. The oil reservoir is easily accessible, allowing users to refill it quickly without hassle.

In terms of user comfort, the Poulan 195506 is designed with an ergonomic handle that provides a secure grip, reducing vibration and strain during operation. This thoughtful design aspect is especially important for users who may be using the chainsaw for prolonged periods.

Additionally, the chainsaw incorporates several safety features, such as the front hand guard and a chain brake, which activate in the case of kickback, providing an extra layer of security for users. The combination of these safety features, along with its manageable weight, makes the Poulan 195506 a user-friendly choice for those at any skill level.

Overall, the Poulan 195506 is a versatile chainsaw that combines power, safety, and ease of use, making it an essential tool for anyone looking to efficiently handle their outdoor cutting tasks. Its reliable performance, attractive features, and robust construction solidify its place as a favored choice among chainsaw enthusiasts.
Top Page Image Contents