Poulan 2001-01, 177110 owner manual Engine, Belts, Transaxle Cooling, Lubrication, Electrical

Page 18

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Open battery box door.

•Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor.

•Rinse the battery with plain water and dry.

•Clean terminals and battery cable ends with wire brush until bright.

•Coat terminals with grease or petro- leum jelly.

•Reinstall battery (See “REPLACING BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual).

V-BELTS

Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear.

TRANSAXLE COOLING

Keep transaxle free from build-up of dirt and chaff which can restrict cooling.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classification SF, or SJ. Select the oil’s SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

 

 

 

 

 

 

 

 

 

 

 

SAE 30

 

 

 

 

 

 

5W-30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

°F

-20°

0°

 

 

30° 32° 40°

 

 

60°

80°

100°

°C

-30°

-20°

-10°

0°

10°

20°

30°

40°

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

Change the oil after every 25 hours of operation or at least once a year if the tractor is not used for 25 hours in one year.

Check the crankcase oil level before starting the engine and after each eight

(8)hours of operation. Tighten oil fill cap/ dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL

Determine temperature range expected before oil change. All oil must meet API service classification SF-SJ.

•Be sure tractor is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

•Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil.

•Remove cap from end of drain valve and install the drain tube onto the fitting.

•Unlock drain valve by pushing inward slightly and turning counterclockwise.

•To open, pull out on the drain valve.

•After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown.

•Remove the drain tube and replace the cap onto to the end of the drain valve.

•Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see

“PRODUCT SPECIFICATIONS” section of this manual.

•Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for accurate reading. Keep oil at “FULL” line on dipstick.

Oil Drain Valve

Drain Tube

Closed and

Locked Position

TRACTOR -- MODEL NUMBER 271470

ELECTRICAL

KEY PART

NO. NO. DESCRIPTION

1144925 Battery 12 Volt 25 Amp

274760412 Bolt, Hex Head 1/4-20 unc x 3/4

8

156417

Case, Battery Mech Hinge

16

153664

Switch, Interlock Push-In

21

166181

Harness, Light Socket (Includes 4152J)

22

4152J

Bulb, Light

244799J Cable, Battery, 6 Gauge, Red, 11"

25146147 Cable, Battery, 6 Gauge, Red, W/16 Wire

26 175158 Fuse

2773510400 Nut Keps Hex 1/4-20 UNC

284207J Cable, Ground, 6 Gauge, Black, 12"

29121305X Switch, Plunger

30175566 Switch, Ignition

33

140401

Key, Ignition

40

170217

Harness, Ignition

41

71110408

Bolt, Hex Head, Fin. 1/4-20 x 1/2

42

131563

Cover, Terminal, Red

43

175141

Solenoid

48

140844

Adaptor Ammeter Rectangular

52

141940

Protection Wire Loop

NOTE: All component dimensions given in U. S. inches 1 inch = 25.4 mm

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, these multi-viscosity oils

will result in increased oil consumption Cap when used above 32°F. Check your

engine oil level more frequently to avoid possible engine damage from running

low on oil.

18

31

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Modelno Table of Contents IV. Service III. ChildrenWash hands after handling Tractor -- Model NumberMower Deck KEY Part DescriptionProduct Specifications Customer ResponsibilitiesSeat Lift AssemblyUnassembled Parts KEY Part NO. NO. DescriptionHOW to SET Upyour Tractor AssemblyTools Required for Assembly To Removetractor from CartonDecals Install SeatWheels and Tires KEY PartCheck for Proper Position of ALL Belts Seat AssemblyTractor -- Model Number Check Tire Pressure Check Deck LevelnessEngine KEY Part NO. no DescriptionOptional Equipment Tractor -- Model Number KnowyourtractorYour Tractor Spark ArresterHOW to Useyour Tractor To Operate Mower Steering To Adjust Mower Cutting HeightTo Operate on Hills To TransportCheck Engine OIL Level Before Starting the EnigneTo Start Engine ADD GasolineTractor -- Model Number Mowing Tips Always operate engine at full throttleChassis and Enclosures MaintenanceLubrication Chart General RecommendationsTractor Transaxle Cooling EngineBelts LubricationAIR Filter Clean AIR ScreenEngine Cooling Fins MufflerSchematic Service and AdjustmentsCleaning To Install MowerTroubleshooting Chart Problem Cause CorrectionTo Level Mower Housing To Replace Mower Blade Drive Belt To Adjust BrakeTo Adjust Steering Wheel ALIGN- Ment To Replace Motion Drive BeltFront Wheel TOE-IN/CAMBER To Start Engine with a Weak BatteryReplacing Battery To Remove Wheel for RepairsStorage To Adjust CarburetorBattery Other

177110, 2001-01 specifications

The Poulan 2001-01,177110 is a powerful and efficient chainsaw designed for various cutting tasks, ranging from light home use to moderate professional applications. A combination of high-performance features and user-friendly design makes it an excellent choice for both novice and experienced users. The chainsaw boasts a robust engine that delivers impressive horsepower, enabling it to handle tougher cutting jobs with ease.

One of the key features of the Poulan 2001-01,177110 is its lightweight and ergonomic design, which enhances user comfort and reduces fatigue during extended use. The chainsaw is equipped with a well-balanced frame that promotes improved maneuverability, allowing users to move easily while cutting. Additionally, the anti-vibration handle helps reduce the amount of vibration felt by the operator, further enhancing comfort during operation.

Powering the Poulan chainsaw is a reliable gas engine that provides consistent performance in various conditions. With features such as an easy-start system, users can quickly get the chainsaw running with minimal effort, making it particularly appealing for those who may be intimidated by traditional starting procedures. The engine is also designed for fuel efficiency, allowing for longer run times between refueling.

The Poulan 2001-01,177110 incorporates a 16-inch bar and chain, providing ample cutting capacity for a range of tasks including trimming branches, cutting firewood, and felling small trees. The chain is designed for sharp cutting and durability, ensuring that users can work effectively without frequent replacements or maintenance. Additionally, the automatic oiler system helps maintain proper lubrication of the chain, promoting prolonged lifespan and reduced maintenance needs.

Safety is a top priority with the Poulan chain saw, as it features a chain brake that can immediately stop the chain in case of kickback. The front handguard is another important safety element that protects the user's hands while operating the chainsaw. Overall, the Poulan 2001-01,177110 stands out for its combination of power, lightweight design, and safety features, making it a popular choice for anyone in need of a versatile and reliable chainsaw for yard work or light professional applications.
Top Page Image Contents