HOW to Useyour Tractor

The operation of any tractor can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glasses or eye shields while operating your tractor or performing any adjustments or repairs. We recommend a wide vision safety mask over spectacles or standard safety glasses.

TRACTOR -- MODEL NUMBER 271470

STEERING

TO SET PARKING BRAKE

Your tractor is equipped with an operator presence sensing switch. When engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine.

•Depress clutch/brake pedal into full “BRAKE” position and hold.

•Place parking brake lever in “EN- GAGED” position and release pres- sure from clutch/brake pedal. Pedal should remain in “BRAKE” position. Make sure parking brake will hold tractor secure.

	Throttle/Choke	Attachment Clutch
	Throttle/Choke	Lever “Engaged”
	Control	Position
		Ignition Key
	Clutch/	“Disengaged”
	Clutch/	Position
	Brake	Position
	Brake	Parking
	Pedal	Parking
		Brake
		“Engaged”
		Position
		Gearshift
	“Brake”	Lever
	“Brake”	“Disengaged”
	Position	“Disengaged”
	Position	Position
		Position

STOPPING

MOWER BLADES -

•To stop mower blades,move attach- ment clutch lever to “DISENGAGED” position.

GROUND DRIVE -

•To stop ground drive, depress clutch/ brake pedal into full “BRAKE” position.

•Move gearshift lever to neutral (N) position.

ENGINE -

•Move throttle control to slow position. NOTE: Failure to move throttle control to slow position and allowing engine to idle before stopping may cause engine to “backfire”.

•Turn ignition key to “OFF” position and remove key. Always remove key when leaving tractor to prevent unauthorized use.

•Never use choke to stop engine. IMPORTANT: Leaving the ignition switch in any position other than "OFF" will cause the battery to be discharged, (dead).

NOTE: Under certain conditions when tractor is standing idle with the engine running, hot engine exhaust gases may cause “browning” of grass. To eliminate this possibility, always stop engine when stopping tractor on grass areas.

CAUTION: Always stop tractor completely, as described above, before leaving the operator's position; to empty grass catcher, etc.

TO USE THROTTLE CONTROL

Always operate engine at full throttle.

•Operating engine at less than full throttle reduces the battery charging rate.

•Full throttle offers the best bagging and mower performance.

TO MOVE FORWARD AND BACK- WARD

The direction and speed of movement is controlled by the gearshift lever.

•Start tractor with clutch/brake pedal depressed and gearshift lever in neutral (N) position.

•Move gearshift lever to desired position.

•Slowly release clutch/brake pedal to start movement.

IMPORTANT: Bring tractor to a complete stop before shifting or changing gears. Failure to do so will shorten the useful life of your transaxle.

KEY PART

NO. NO. DESCRIPTION

1140044X428 Steering Wheel

2154427 Axle Assembly STMP Dropped STL

3156483 Spindle Assembly, L.H.

4157473 Spindle Assembly, R.H.

6266H

Bearing, Race, Thrust, Hardened

6121748X Washer 25/32 x 1-5/8 x 16 Gauge

719272016 Washer 27/32 x 1-1/4 x 16 Gauge

8	12000029	Ring, Klip
9	3366R	Bearing, Steering Column
10	169832	Draglink
11	10040600	Washer, Lock
13	136518	Spacer Bearing Axle Front
15	145212	Hexflange Lock

17156546 Shaft Assembly, Steering

1857079 Washer, Thrust .515 x .750 x .033

19160395 Support, Shaft

22165857 Screw, Hex Wshhd

23165851 Pittman Shaft Assembly

25	154406	Bracket, Steering
26	126847X	Bushing, Link, Drag
27	136874	Gear, Sector

2819131416 Washer 13/32 x 7/8 x 16 Gauge

2917060612 Screw, 3/8-16 x 3/4

3076020412 Pin

32	130465	Rod, Tie
36	155099	Bushing, Steering
37	152927	Screw

38140045X428 Cap, Steering Wheel

3919133812 Washer 13/32 x 2-3/8 x 12 Gauge

7810H

Gripco Nut

41100711L Adaptor, Steering Wheel

42145054X428 Boot, Steering

43121749X Washer 25/32 x 1-1/4 x 16 Gauge

44153720 Shaft Extension Steering

46	121232X	Cap, Spindle
47	6855M	Fitting, Grease
51	73800500	Nut lock Hex w/Ins 5/16-18
54	74780520	Bolt Fin Hex 5/16-18 UNC x 1-1/4

62167902 Kit Steering Asm Service

6374780616 Bolt Fin Hex 3/8-16 x 1-1/4

65	160367	Spacer Brace Axle
66	154404	Bearing Arm Pittman
67	72140618	Bolt, Rdhd Sq 3/8-16 UNC x 2-1/4
68	169827	Axle, Brace

7919132012 Washer 13/32 x 1-1/4 x 12 Ga.

8074950612 Bolt Hex Nylon 3/8-16 x 3/4

82	169835	Bracket Susp Chassis Front
85	133835	Fastener Christmas Tree

NOTE: All component dimensions given in U. S. inches 1 inch = 25.4 mm

177110, 2001-01 specifications

The Poulan 2001-01,177110 is a powerful and efficient chainsaw designed for various cutting tasks, ranging from light home use to moderate professional applications. A combination of high-performance features and user-friendly design makes it an excellent choice for both novice and experienced users. The chainsaw boasts a robust engine that delivers impressive horsepower, enabling it to handle tougher cutting jobs with ease.

One of the key features of the Poulan 2001-01,177110 is its lightweight and ergonomic design, which enhances user comfort and reduces fatigue during extended use. The chainsaw is equipped with a well-balanced frame that promotes improved maneuverability, allowing users to move easily while cutting. Additionally, the anti-vibration handle helps reduce the amount of vibration felt by the operator, further enhancing comfort during operation.

Powering the Poulan chainsaw is a reliable gas engine that provides consistent performance in various conditions. With features such as an easy-start system, users can quickly get the chainsaw running with minimal effort, making it particularly appealing for those who may be intimidated by traditional starting procedures. The engine is also designed for fuel efficiency, allowing for longer run times between refueling.

The Poulan 2001-01,177110 incorporates a 16-inch bar and chain, providing ample cutting capacity for a range of tasks including trimming branches, cutting firewood, and felling small trees. The chain is designed for sharp cutting and durability, ensuring that users can work effectively without frequent replacements or maintenance. Additionally, the automatic oiler system helps maintain proper lubrication of the chain, promoting prolonged lifespan and reduced maintenance needs.

Safety is a top priority with the Poulan chain saw, as it features a chain brake that can immediately stop the chain in case of kickback. The front handguard is another important safety element that protects the user's hands while operating the chainsaw. Overall, the Poulan 2001-01,177110 stands out for its combination of power, lightweight design, and safety features, making it a popular choice for anyone in need of a versatile and reliable chainsaw for yard work or light professional applications.