Poulan 197498 manual To Replace Mower Blade Drive Belt See Fig, Belt Removal, Belt Installation

Page 20

SERVICE AND ADJUSTMENTS

SIDE-TO-SIDE ADJUSTMENT (See Figs. 17 and 18)

•Raise mower to its highest position.

•At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

•If adjustment is necessary, make adjustment on one side of mower only.

•To raise one side of mower, tighten lift link adjustment nut on that side.

•To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Three full turns of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE OF

 

BOTTOM EDGE

MOWER

 

OF MOWER

TO GROUND

 

TO GROUND

“A”

GROUND LINE

“A”

FIG. 17

SUSPENSION ARM

LIFT LINK ADJUSTMENT NUT

FIG. 18

FRONT-TO-BACK ADJUSTMENT (See Figs. 19 and 20)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

MANDREL

"D"

"D"

FIG. 19

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT "F"

NUT "E"

TRUNNION

FRONT LINKS

FIG. 20

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 21)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Install new belt in reverse order of removal.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower in reverse order of removal instruc- tions.

MANDREL

IDLER

PULLEY

PULLEYS

MANDREL

 

PULLEY

 

FIG. 21

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents XT24H42LT Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService General ServiceIII. Children IV. TowingTable of Contents Unassembled Parts Steering Wheel Gauge WheelsSeat Key Slope SheetAssembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Assemble Gauge Wheels to Mower Deck See Fig Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Using the Reverse Operation System To Operate Mower See FigReverse Operation System ROS To Operate on HillsBefore Starting the Engine Check Engine OIL LevelADD Gasoline To Start Engine See FigAutomatic Transmission Warm UP Mowing TipsPurge Transmission Maintenance Lubrication ChartGeneral Recommendations Before Each USETo Sharpen Blade See Fig TractorBlade Removal See Fig Engine Cleaning Service and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigBelt Removal Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake Transaxle Motion Control Lever Neutral Adjustment See FigSee Fig To Replace Motion Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight Bulb Interlocks and RelaysStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

197498 specifications

The Poulan 197498 is a versatile and high-performing piece of outdoor equipment designed primarily for lawn care enthusiasts and professionals alike. Known for its reliability and efficiency, this product delivers an impressive array of features that cater to various mowing needs.

At the heart of the Poulan 197498 is its powerful engine, which provides robust performance capable of tackling even the toughest grass and terrain. This engine is engineered for optimal fuel efficiency, allowing users to maximize their mowing time without frequent refueling. Its starting system is designed for user-friendliness, featuring advanced technology that minimizes start-up issues, ensuring a hassle-free experience.

One of the standout features of the Poulan 197498 is its cutting deck. With a wide cutting path, this mower can cover more ground in less time, making it an ideal choice for larger lawns. The adjustable cutting height settings allow users to customize their mowing experience based on grass type and desired length. This flexibility ensures a clean and professional finish every time.

In terms of technology, the Poulan 197498 incorporates innovative engineering that enhances maneuverability. Its lightweight design, coupled with smooth-rolling wheels, enables easy navigation around obstacles, making it suitable for intricate yard layouts. The mower's ergonomic handles provide a comfortable grip, reducing fatigue during extended use.

Durability is another key characteristic of the Poulan 197498. Constructed with high-quality materials, this mower is built to withstand the rigors of regular use. Its robust chassis and reliable components ensure longevity, making it a wise investment for anyone serious about lawn maintenance.

Additionally, the Poulan 197498 features easy maintenance solutions. Quick-release mechanisms allow for straightforward blade changes and deck cleaning, keeping the mower in optimal working condition and prolonging its lifespan.

In conclusion, the Poulan 197498 stands out as a reliable and efficient lawn mower, blending power, versatility, and durability into one impressive machine. Its user-friendly features and advanced technologies make it an excellent choice for both residential homeowners and professional landscapers seeking an effective solution for their mowing tasks. With the Poulan 197498, achieving a perfectly manicured lawn is just a mow away.
Top Page Image Contents