Poulan 197498 manual Transmission REMOVAL/REPLACEMENT, To Adjust Steering Wheel ALIGN- Ment

Page 22

SERVICE AND ADJUSTMENTS

•While holding motion control lever in place, loosen the adjustment bolt.

•Move motion control lever to the neutral (N) (lock gate) position.

•Tighten adjustment bolt securely.

NOTE: If additional clearance is needed to get to adjustment bolt, move mower deck height to the lowest position.

After above adjustment is made, if the tractor still creeps forward or backward while motion control lever is in neutral position, follow these steps:

•Loosen the adjustment bolt.

•Move the motion control lever 1/4 to 1/2 inch in the direction it is trying to creep.

•Tighten adjustment bolt securely.

•Start engine and test.

•If tractor still creeps, repeat above steps until satis- fied.

MOTION CONTROL

NEUTRAL

LEVER

LOCK GATE

 

ADJUSTMENT

BOLT

FIG. 24

TRANSMISSION REMOVAL/REPLACEMENT

Should your transmission require removal for service or replacement, it should be purged after reinstallation and before operating the tractor. See“PURGETRANSMISSION” in the Operation section of this manual.

TO ADJUST STEERING WHEEL ALIGN- MENT

If steering wheel crossbars are not horizontal (left to right) when wheels are positioned straight forward, remove steer- ing wheel and reassemble per instructions in the Assembly section of this manual.

FRONT WHEEL TOE-IN/CAMBER

The front wheel toe-in and camber are not adjustable on your tractor.If damage has occurred to affect the front wheel toe-in or camber, contact your nearest authorized service center/department.

TO REMOVE WHEEL FOR REPAIRS (See Fig. 25)

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE COVER

SQUARE KEY (REAR

WHEEL ONLY)

FIG. 25

TO START ENGINE WITH A WEAK BATTERY (See Fig. 26)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the MAINTENANCE sec- tion of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

WEAK OR DEAD BATTERY

FULLY CHARGED

BATTERY

FIG. 26

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents XT24H42LT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Seat Unassembled PartsSteering Wheel Gauge Wheels Key Slope SheetTo Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check Deck Levelness Assemble Gauge Wheels to Mower Deck See FigCheck Tire Pressure Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS Using the Reverse Operation SystemTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineCheck Engine OIL Level To Start Engine See FigPurge Transmission Mowing TipsAutomatic Transmission Warm UP General Recommendations MaintenanceLubrication Chart Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Engine Cleaning To Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig Belt InstallationBelt Removal See Fig To Check and Adjust BrakeTransaxle Motion Control Lever Neutral Adjustment See Fig To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Transmission REMOVAL/REPLACEMENTTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control Interlocks and RelaysFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Service Notes Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

197498 specifications

The Poulan 197498 is a versatile and high-performing piece of outdoor equipment designed primarily for lawn care enthusiasts and professionals alike. Known for its reliability and efficiency, this product delivers an impressive array of features that cater to various mowing needs.

At the heart of the Poulan 197498 is its powerful engine, which provides robust performance capable of tackling even the toughest grass and terrain. This engine is engineered for optimal fuel efficiency, allowing users to maximize their mowing time without frequent refueling. Its starting system is designed for user-friendliness, featuring advanced technology that minimizes start-up issues, ensuring a hassle-free experience.

One of the standout features of the Poulan 197498 is its cutting deck. With a wide cutting path, this mower can cover more ground in less time, making it an ideal choice for larger lawns. The adjustable cutting height settings allow users to customize their mowing experience based on grass type and desired length. This flexibility ensures a clean and professional finish every time.

In terms of technology, the Poulan 197498 incorporates innovative engineering that enhances maneuverability. Its lightweight design, coupled with smooth-rolling wheels, enables easy navigation around obstacles, making it suitable for intricate yard layouts. The mower's ergonomic handles provide a comfortable grip, reducing fatigue during extended use.

Durability is another key characteristic of the Poulan 197498. Constructed with high-quality materials, this mower is built to withstand the rigors of regular use. Its robust chassis and reliable components ensure longevity, making it a wise investment for anyone serious about lawn maintenance.

Additionally, the Poulan 197498 features easy maintenance solutions. Quick-release mechanisms allow for straightforward blade changes and deck cleaning, keeping the mower in optimal working condition and prolonging its lifespan.

In conclusion, the Poulan 197498 stands out as a reliable and efficient lawn mower, blending power, versatility, and durability into one impressive machine. Its user-friendly features and advanced technologies make it an excellent choice for both residential homeowners and professional landscapers seeking an effective solution for their mowing tasks. With the Poulan 197498, achieving a perfectly manicured lawn is just a mow away.
Top Page Image Contents