Poulan 197498 manual To Check and Adjust Brake, To Replace Motion Drive Belt See Fig

Page 21

SERVICE AND ADJUSTMENTS

TO CHECK AND ADJUST BRAKE

(See Fig. 22)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be checked and adjusted.

TO CHECK BRAKE

•Park tractor on a level, dry concrete or paved surface, depress clutch/brake pedal all the way down and en- gage parking brake.

•Disengage transmission by placing freewhel control in “transmission disengaged” position. Pull freewheel control out and into the slot and release so it is held in the disengaged position.

The rear wheels must lock and skid when you try to manually push the tractor forward. If the rear wheels rotate, the brake needs to be adjusted or the pads need to be replaced.

TO ADJUST BRAKE

•Depress clutch/brake pedal all the way down and en- gage parking brake.

•Measure distance between brake operating arm and nut “A” on brake rod.

•If distance is other than 1-9/16", loosen jam nut and turn nut “A” until distance becomes 1-9/16". Retighten jam nut against nut “A”.

•Engage transmission by placing freewheel control in “transmission engaged” position.

•Road test tractor for proper stopping distance as stated above. Readjust if necessary. If stopping distance is still greater than five (5) feet in highest gear, further maintenance is necessary. Replace brake pads or contact a qualified service center.

WITH PARKING BRAKE “ENGAGED”

NUT “A”

1-9/16”

JAM NUT

 

OPERATING

ARM

01513

DO NOT TOUCH THIS NUT. IF FURTHER

BRAKE ADJUSTMENT IS NECESSARY CON-

TACT YOUR NEAREST AUTHORIZED SERVICE

CENTER/DEPARTMENT

FIG. 22

TO REPLACE MOTION DRIVE BELT (See Fig. 23)

Park the tractor on level surface. Engage parking brake. For assistance, there is a belt installation guide decal on bottom side of left footrest.

BELT REMOVAL -

•Remove mower (See “TO REMOVE MOWER” in this section of manual).

NOTE: Observe entire motion drive belt and position of all belt guides and keepers.

•Remove belt from stationary idler and clutching idler.

•Remove belt downward from around engine pulley.

•Pull belt slack toward rear of tractor. Carefully remove belt upwards from transmission input pulley and over cooling fan blades.

•Remove belt from center span keeper and pull belt away from tractor.

BELT INSTALLATION -

•Carefully work new belt down around transmission cooling fan and onto the input pulley.

•Slide belt into the center span keeper.

•Pull belt toward front of tractor and roll around the top groove of engine pulley.

•Install belt through stationary idler and clutching idler.

•Make sure belt is in all pulley grooves and inside all belt guides and keepers.

•Install mower (See “TO INSTALL MOWER” in this sec- tion of manual).

ENGINE

PULLEY

CLUTCHING

IDLER

STATIONARY

IDLER

TRANSMISSION

INPUT PULLEYCENTER SPAN KEEPER

FIG. 23

TRANSAXLE MOTION CONTROL LEVER NEUTRAL ADJUSTMENT (See Fig. 24)

The motion control lever has been preset at the factory and adjustment should not be necessary.

•Loosen adjustment bolt in front of the right rear wheel, and lightly tighten.

•Start engine and move motion control lever until tractor does not move forward or backward.

•Hold motion control lever in that position and turn engine

21 off.

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Always Wear EYE Protection During Operation XT24H42LTSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationGeneral Service ServiceIII. Children IV. TowingTable of Contents Steering Wheel Gauge Wheels Unassembled PartsSeat Key Slope SheetTools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Assemble Gauge Wheels to Mower Deck See FigCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig Using the Reverse Operation SystemReverse Operation System ROS To Operate on HillsCheck Engine OIL Level Before Starting the EngineADD Gasoline To Start Engine See FigMowing Tips Purge TransmissionAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Engine Cleaning To Install Mower See Fig Service and AdjustmentsTo Level Mower Housing To Remove Mower See FigBelt Installation To Replace Mower Blade Drive Belt See FigBelt Removal Transaxle Motion Control Lever Neutral Adjustment See Fig To Check and Adjust BrakeSee Fig To Replace Motion Drive Belt See FigTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace Headlight Bulb Interlocks and RelaysOther StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsEngine dies when Limited Warranty Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

197498 specifications

The Poulan 197498 is a versatile and high-performing piece of outdoor equipment designed primarily for lawn care enthusiasts and professionals alike. Known for its reliability and efficiency, this product delivers an impressive array of features that cater to various mowing needs.

At the heart of the Poulan 197498 is its powerful engine, which provides robust performance capable of tackling even the toughest grass and terrain. This engine is engineered for optimal fuel efficiency, allowing users to maximize their mowing time without frequent refueling. Its starting system is designed for user-friendliness, featuring advanced technology that minimizes start-up issues, ensuring a hassle-free experience.

One of the standout features of the Poulan 197498 is its cutting deck. With a wide cutting path, this mower can cover more ground in less time, making it an ideal choice for larger lawns. The adjustable cutting height settings allow users to customize their mowing experience based on grass type and desired length. This flexibility ensures a clean and professional finish every time.

In terms of technology, the Poulan 197498 incorporates innovative engineering that enhances maneuverability. Its lightweight design, coupled with smooth-rolling wheels, enables easy navigation around obstacles, making it suitable for intricate yard layouts. The mower's ergonomic handles provide a comfortable grip, reducing fatigue during extended use.

Durability is another key characteristic of the Poulan 197498. Constructed with high-quality materials, this mower is built to withstand the rigors of regular use. Its robust chassis and reliable components ensure longevity, making it a wise investment for anyone serious about lawn maintenance.

Additionally, the Poulan 197498 features easy maintenance solutions. Quick-release mechanisms allow for straightforward blade changes and deck cleaning, keeping the mower in optimal working condition and prolonging its lifespan.

In conclusion, the Poulan 197498 stands out as a reliable and efficient lawn mower, blending power, versatility, and durability into one impressive machine. Its user-friendly features and advanced technologies make it an excellent choice for both residential homeowners and professional landscapers seeking an effective solution for their mowing tasks. With the Poulan 197498, achieving a perfectly manicured lawn is just a mow away.
Top Page Image Contents