Poulan 412523, 96042004900 ADD Gasoline, To Start Engine See Fig, Purge Transmission, Running

Page 12

OPERATION

ADD GASOLINE

•Fill fuel tank to bottom of filler neck. Do not overfill. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. (Use of leaded gasoline will increase carbon and lead oxide deposits and reduce valve life). Do not mix oil with gasoline. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness.

CAUTION: Wipe off any spilled oil or fuel. Do not store, spill or use gasoline near an open flame.

IMPORTANT: WHEN OPERATING IN TEMPERATURES BELOW32°F(0°C), USE FRESH, CLEAN WINTER GRADE GASOLINE TO HELP INSURE GOOD COLD WEATHER STARTING.

CAUTION: Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. See Storage Instructions for additional information. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur.

TO START ENGINE (See Fig. 3)

When starting the engine for the first time or if the engine has run out of fuel, it will take extra cranking time to move fuel from the tank to the engine.

•Be sure freewheel control is in the transmission engaged position.

•Sit on seat in operating position, depress brake pedal and set parking brake.

•Move attachment clutch to “DISENGAGED” position.

•Move throttle control to fast position

•Pull choke control out for a cold engine start attempt. For a warm engine start attempt the choke control may not be needed.

NOTE: Before starting, read the warm and cold starting procedures below.

•Insert key into ignition and turn key clockwise to “START” position and release key as soon as engine starts. Do not run starter continuously for more than fifteen seconds per minute. If the engine does not start after several attempts, push choke control in, wait a few minutes and try again. If engine still does not start, pull the choke control out and retry.

WARM WEATHER STARTING (50° F and above)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly.

•The attachments and ground drive can now be used. If the engine does not accept the load, restart the engine and allow it to warm up for one minute using the choke as described above.

COLD WEATHER STARTING (50° F and below)

•When engine starts, slowly push choke control in until the engine begins to run smoothly. Continue to push the choke control in small steps allowing the engine to accept small changes in speed and load, until the choke control is fully in. If the engine starts to run roughly, pull the choke control out slightly for a few seconds and then continue to push the control in slowly. This may require an engine warm-up period from several seconds to several minutes, depending on the temperature.

AUTOMATIC TRANSMISSION WARM UP

•Before driving the unit in cold weather, the transmission should be warmed up as follows:

•Be sure the tractor is on level ground.

•Release the parking brake and let the brake slowly return to operating position.

•Allow one minute for transmission to warm up. This can be done during the engine warm up period.

•The attachments can be used during the engine warm-up period after the transmission has been warmed up and may require the choke control be pulled out slightly.

NOTE: If at a high altitude (above 3000 feet) or in cold temperatures (below 32 F) the carburetor fuel mixture may need to be adjusted for best engine performance. See “TO ADJUST CARBURETOR” in the Service and Adjustments section of this manual.

PURGE TRANSMISSION

CAUTION: Never engage or disengage freewheel lever while the engine is

running.

To ensure proper operation and performance, it is recom- mended that the transmission be purged before operating tractor for the first time. This procedure will remove any trapped air inside the transmission which may have de- veloped during shipping of your tractor.

IMPORTANT: SHOULD YOUR TRANSMISSION REQUIRE REMOVAL FOR SERVICE OR REPLACEMENT, IT SHOULD BE PURGED AFTER REINSTALLATION BEFORE OPERATING THE TRACTOR.

1.Place tractor safely on a level surface - that is clear and open - with engine off and parking brake set.

2.Disengage transmission by placing freewheel control in disengaged position (See “TO TRANSPORT” in this section of manual).

3.Sitting in the tractor seat, start engine. After the en- gine is running, move throttle control to slow position. Disengage parking brake

CAUTION: At any time, during step 4, there may be movement of the drive wheels.

4.Depress forward drive pedal to full forward position, hold for five (5) seconds and release pedal. Depress reverse drive pedal to full reverse position, hold for five

(5) seconds and release pedal. Repeat this procedure three (3) times.

5.Shut- off engine and set parking brake.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents CO20H46YT ModelSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationService III. ChildrenIV. Towing Table of Contents Assembly Unassembled PartsTo Remove Tractor from Carton Unpack CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Ignition Switch Used for starting and stopping the engine Know Your TractorHOW to USE Your Tractor To SET Parking BRAKESee FigStopping See Fig To USE Throttle Control D See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo Move Forward and Backward See Fig To USE Cruise Control -J See FigBefore Starting the Engine Reverse Operation System ROSTo Transport See Figs To Operate on HillsADD Gasoline To Start Engine See FigPurge Transmission Automatic Transmission Warm UPMowing Tips Maintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBrake Operation TiresEngine Cleaning Engine OIL FilterMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Turn nut right Turn nut left To raise mower To lower mowerBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty L5V 3E4Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeParts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés MAX Dentretien Remarques Autorisé Garantie cette de exclus sont normal l’entretien etInitiale d’achat date la de compter à jours 90 dix Dépannage DE Guide Connexions les et interrupteurs les câblage, le VérifiezLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage Starter DU Commande LA Régler Pour GAZ DES CommandeReglages ET Revision Carburateur LE Régler PourFig la Voir Tionsraparé LES Pour Roues LES Enlever Pour Avant Roue LA DE PINCEMENT/CARROSSAGE29 .FIG 28 .FIGRéglages ET Révision Fig la Voir D’ENTRAÎNEMENT Courroie LA Remplacer PourFIG LA Voir Tondeuse DE Lame DE MentnetraîTondeuse LA Niveau LE Ajuster Pour 25 .FIG24 .FIG 23 .FIG21 .FIG 19 .FIG 20 .FIG18 .FIG Place en bien est courroie la que vous-Assurez ImportantCourroie LA ET Tondeuse LA Installer Fig VoirTondeuse LA Enlever Pour 17.FIGEntretien Fig la Voir’ALLUMAGE Bougie Moteur DE D’HUILE FiltreAIR À Filtre ’AIR Tamis LE NettoyerSionmistrans LA DE Moteur Fluide Transmission LA DE RefroidissementFig la Voir Lame LA Enlever EN Fonctionnement DE Système ETLubrification DE Tableau Utilisation Chaque AvantAvant ET Réinstallation LA Après Purgée Être UtilisationTransmission LA Purger 12 .FIGE T O M O P’ESSENCE Réservoir LE Remplir Moteur DU D’HUILE Niveau LE VérifierAccessoires Autres ET Charrettes DES Remorquer Pour 11 et 3 .Fig les VoirMAR EN Fonctionnement DE Système Tondeuse LA Utiliser Pour VitessDE Régulateur LE Utiliser Comment Fig laGAZ DES Commande LA Utiliser Pour S I L I T UFig la Voir Mentnetionsta DE Frein LE Engager Pour Fig la Voir Arrêter Pour 4 .FIGFroid moteur un démarrer de permet Détrangleur Commande Moteur de vitesse la commander de permet GAZ DES Commande D’EMBRAYAGE Montage Desmancom des tionfonc la etTionsec la Voir Conduisant LE EN Telet PA LA DE Tracteur LE Retirer PourMontées NON Piéces Toncar DU Tracteur LE Sortir PourR E T T a B I F I R É Sommaire Général Entretien Tracteurs des sécurité touteEn l’utilisation pour Conseils ’ESSENCE DE Sûre ManipulationPentes LES Dans FonctionnementTracteurs des sécurité toute en l’utilisation pour Conseils AUX Imprimé

96042004900, 412523 specifications

The Poulan 412523,96042004900 is a versatile and efficient chainsaw designed for both homeowners and professionals seeking reliable performance for various cutting tasks. Whether it's trimming branches, felling small trees, or tackling firewood, this chainsaw is equipped to handle a range of applications with ease.

One of the main features of the Poulan 412523 is its powerful engine, which typically provides a high power-to-weight ratio, allowing for efficient cutting while minimizing user fatigue. The chainsaw's engine design ensures smooth operation and quick starts, making it a user-friendly tool for both experienced users and novices. Its lightweight frame contributes to its maneuverability, making it easier to handle during extended use.

The chainsaw is equipped with a quality bar and chain that delivers excellent cutting performance. The chain's design ensures optimal cutting efficiency while being able to withstand significant wear, which is essential for heavy-duty tasks. The bar length is designed to handle various cutting depths, allowing users to make precise cuts as needed.

Safety is a paramount concern with any chainsaw, and the Poulan 412523 addresses this with several integrated safety features. These include a chain brake, which quickly stops the chain upon sudden release, and a safety throttle that prevents accidental engagement. Moreover, the ergonomic handle design offers a secure grip, reducing the risk of slippage while cutting.

Technology-wise, this chainsaw incorporates an efficient fuel system that promotes better fuel economy and lower emissions. This is particularly important in today’s environmental landscape, as operators seek to minimize their carbon footprint while working with power tools. Additionally, the Poulan 412523 features an easy-access air filter, which simplifies maintenance and ensures optimal engine performance by keeping dirt and debris at bay.

Another standout characteristic of this chainsaw is its durability. Made with robust materials, the Poulan 412523 is built to withstand harsh working conditions, ensuring a long lifespan. Coupled with regular maintenance, users can expect a reliable performance over many seasons.

In conclusion, the Poulan 412523,96042004900 is a well-rounded chainsaw offering a blend of power, safety, and user-friendly features. With its smart design and advanced technologies, it is suitable for various cutting tasks and is a valuable addition to any toolkit, whether for professional landscapers or enthusiastic homeowners.
Top Page Image Contents