Poulan 412523 manual To Level Mower, Turn nut right Turn nut left To raise mower To lower mower

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER

Make sure tires are properly inflated to the PSI shown on tires. If tires are over or under inflated, it may affect the appearance of your lawn and lead you to think the mower is not adjusted properly.

VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig.22)

•With all tires properly inflated and if your lawn appears unevenly cut, determine which side of mower is cutting lower.

•With a 3/4" or adjustable wrench, turn lift link adjust- ment nut (A) to the left to lower LH side of mower, or, to the right to raise LH side of mower.

 

A

Turn nut right

Turn nut left

to raise mower

to lower mower

02948

 

FIG. 22

NOTE: Each full turn of adjustment nut will change mower height about 3/16".

•Test your adjustment by mowing some uncut grass and visually checking the appearance. Readjust, if necessary, until you are satisfied with the results.

PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 23)

•With all tires properly inflated, park tractor on level ground or driveway.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to its highest position.

•At both sides of mower, position blade at side and measure the distance (A) from bottom edge of blade to the ground. The distance should be the same on both sides.

 

02966

A

A

FIG. 23

•If adjustment is necessary, see step in Visual Adjust- ment instructions above.

•Recheck measurements, adjust if necessary until both sides are equal.

FRONT-TO-BACK ADJUSTMENT (See Figs. 24 and 25) IMPORTANT: Deck must be level side-to-side.

To obtain the best cutting results, the mower blades should be adjusted so the front tip is 1/8" to 1/2" lower than the rear tip when the mower is in its highest position.

CAUTION: Blades are sharp. Protect your hands with gloves and/or wrap blade with heavy cloth.

•Raise mower to highest position.

•Position any blade so the tip is pointing straight forward. Measure distance (B) to the ground at front and rear tip of the blade.

•If front tip of blade is not 1/8" to 1/2" lower than the rear

02548

BB

FIG. 24

tip, go to the front of tractor.

•With an 11/16" or adjustable wrench, loosen jam nut A several turns to clear adjustment nut B.

•With a 3/4" or adjustable wrench, turn front link adjust- ment nut (B) clockwise (ltighten) to raise the front of mower, or, counterclockwise (loosen) to lower the front mower.

B

A

Tighten adjust nut

Loosen adjust

B to raise mower

nut B to lower

02950

mower

 

Loosen jam nut A first

FIG. 25

NOTE: Each full turn of the adjustment nut will change mower height about 1/8".

•Recheck measurements, adjust if necessary until front tip of blade is 1/8" to 1/2" lower than the rear tip.

•Hold adjustment nut in position with wrench and tighten jam nut securely against adjustment nut.

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents CO20H46YT ModelSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Assembly Unassembled PartsTo Remove Tractor from Carton Unpack CartonCheck Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Ignition Switch Used for starting and stopping the engine Know Your TractorHOW to USE Your Tractor To SET Parking BRAKESee FigStopping See Fig To USE Throttle Control D See FigTo Adjust Mower Cutting Height See Fig To Adjust Gauge Wheels See FigTo Move Forward and Backward See Fig To USE Cruise Control -J See FigBefore Starting the Engine Reverse Operation System ROSTo Transport See Figs To Operate on HillsADD Gasoline To Start Engine See FigPurge Transmission Automatic Transmission Warm UPMowing Tips Maintenance MaintenanceGeneral Recommendations ScheduleBattery TractorBrake Operation TiresEngine Cleaning Engine OIL FilterMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower Turn nut right Turn nut left To raise mower To lower mowerBelt Installation To Replace Mower Blade Drive Belt See FigTo Check Brake To Replace Motion Drive Belt See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs See Fig To Attach Jumper CablesTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace Headlight BulbStorage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty L5V 3E4Service Notes Only Ride UP and Down Hill Not Across Hill Degrees MAX Fold Along This Dotted Line Degree SlopeParts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés MAX Dentretien Remarques Initiale d’achat date la de compter à jours 90 dix AutoriséGarantie cette de exclus sont normal l’entretien et Dépannage DE Guide Connexions les et interrupteurs les câblage, le VérifiezLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage Starter DU Commande LA Régler Pour GAZ DES CommandeReglages ET Revision Carburateur LE Régler PourFig la Voir Tionsraparé LES Pour Roues LES Enlever Pour Avant Roue LA DE PINCEMENT/CARROSSAGE29 .FIG 28 .FIGRéglages ET Révision Fig la Voir D’ENTRAÎNEMENT Courroie LA Remplacer PourFIG LA Voir Tondeuse DE Lame DE MentnetraîTondeuse LA Niveau LE Ajuster Pour 25 .FIG24 .FIG 23 .FIG21 .FIG 19 .FIG 20 .FIG18 .FIG Place en bien est courroie la que vous-Assurez ImportantCourroie LA ET Tondeuse LA Installer Fig VoirTondeuse LA Enlever Pour 17.FIGEntretien Fig la Voir’ALLUMAGE Bougie Moteur DE D’HUILE FiltreAIR À Filtre ’AIR Tamis LE NettoyerSionmistrans LA DE Moteur Fluide Transmission LA DE RefroidissementFig la Voir Lame LA Enlever EN Fonctionnement DE Système ETLubrification DE Tableau Utilisation Chaque AvantAvant ET Réinstallation LA Après Purgée Être UtilisationTransmission LA Purger 12 .FIGE T O M O P’ESSENCE Réservoir LE Remplir Moteur DU D’HUILE Niveau LE VérifierMAR EN Fonctionnement DE Système Accessoires Autres ET Charrettes DES Remorquer Pour11 et 3 .Fig les Voir Tondeuse LA Utiliser Pour VitessDE Régulateur LE Utiliser Comment Fig laGAZ DES Commande LA Utiliser Pour S I L I T UFig la Voir Mentnetionsta DE Frein LE Engager Pour Fig la Voir Arrêter Pour 4 .FIGFroid moteur un démarrer de permet Détrangleur Commande Moteur de vitesse la commander de permet GAZ DES Commande D’EMBRAYAGE Montage Desmancom des tionfonc la etTionsec la Voir Conduisant LE EN Telet PA LA DE Tracteur LE Retirer PourR E T T a B I F I R É Montées NON PiécesToncar DU Tracteur LE Sortir Pour Sommaire Général Entretien Tracteurs des sécurité touteEn l’utilisation pour Conseils ’ESSENCE DE Sûre ManipulationTracteurs des sécurité toute en l’utilisation pour Conseils PentesLES Dans Fonctionnement AUX Imprimé

96042004900, 412523 specifications

The Poulan 412523,96042004900 is a versatile and efficient chainsaw designed for both homeowners and professionals seeking reliable performance for various cutting tasks. Whether it's trimming branches, felling small trees, or tackling firewood, this chainsaw is equipped to handle a range of applications with ease.

One of the main features of the Poulan 412523 is its powerful engine, which typically provides a high power-to-weight ratio, allowing for efficient cutting while minimizing user fatigue. The chainsaw's engine design ensures smooth operation and quick starts, making it a user-friendly tool for both experienced users and novices. Its lightweight frame contributes to its maneuverability, making it easier to handle during extended use.

The chainsaw is equipped with a quality bar and chain that delivers excellent cutting performance. The chain's design ensures optimal cutting efficiency while being able to withstand significant wear, which is essential for heavy-duty tasks. The bar length is designed to handle various cutting depths, allowing users to make precise cuts as needed.

Safety is a paramount concern with any chainsaw, and the Poulan 412523 addresses this with several integrated safety features. These include a chain brake, which quickly stops the chain upon sudden release, and a safety throttle that prevents accidental engagement. Moreover, the ergonomic handle design offers a secure grip, reducing the risk of slippage while cutting.

Technology-wise, this chainsaw incorporates an efficient fuel system that promotes better fuel economy and lower emissions. This is particularly important in today’s environmental landscape, as operators seek to minimize their carbon footprint while working with power tools. Additionally, the Poulan 412523 features an easy-access air filter, which simplifies maintenance and ensures optimal engine performance by keeping dirt and debris at bay.

Another standout characteristic of this chainsaw is its durability. Made with robust materials, the Poulan 412523 is built to withstand harsh working conditions, ensuring a long lifespan. Coupled with regular maintenance, users can expect a reliable performance over many seasons.

In conclusion, the Poulan 412523,96042004900 is a well-rounded chainsaw offering a blend of power, safety, and user-friendly features. With its smart design and advanced technologies, it is suitable for various cutting tasks and is a valuable addition to any toolkit, whether for professional landscapers or enthusiastic homeowners.
Top Page Image Contents