Poulan 96042004900, 412523 manual Tractor, Brake Operation, Tires, Blade Care, Battery

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See PSI on tires).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

ROS "ON" Position

Engine "ON" Position

(Normal Operating)

 

02828

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

BLADE CARE

For best results mower blades must be sharp. Replace worn, bent or damaged blades.

CAUTION: Useonlyareplacementblade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 13)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new blade with stamped "GRASS SIDE" facing the ground.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: Special blade bolt is heat treated.

BLADE

 

 

MANDREL

 

 

 

ASSEMBLY

 

CENTER

 

 

 

HOLE

 

 

BLADE BOLT

 

 

 

(SPECIAL)

0

2

544

 

 

 

 

 

 

 

 

 

STAR

FIG. 13

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Remove terminal guard.

•Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model CO20H46YTII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationService III. ChildrenIV. Towing Table of Contents Unpack Carton AssemblyUnassembled Parts To Remove Tractor from CartonCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor Ignition Switch Used for starting and stopping the engineTo USE Throttle Control D See Fig HOW to USE Your TractorTo SET Parking BRAKESee Fig Stopping See FigTo USE Cruise Control -J See Fig To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig To Move Forward and Backward See FigTo Operate on Hills Before Starting the EngineReverse Operation System ROS To Transport See FigsAutomatic Transmission Warm UP ADD GasolineTo Start Engine See Fig Purge TransmissionMowing Tips Schedule MaintenanceMaintenance General RecommendationsTires BatteryTractor Brake OperationEngine Spark Plugs CleaningEngine OIL Filter MufflerService and Adjustments To Install Mower See FigTo Remove Mower See Fig Install belt on engine pulley M, in belt keepers G Turn nut right Turn nut left To raise mower To lower mower To Level MowerTo Replace Motion Drive Belt See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig To Check BrakeTo Attach Jumper Cables To Start Engine with a Weak Battery See FigFront Wheel TOE-IN/CAMBER To Remove Wheel for Repairs See FigTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when L5V 3E4 Limited WarrantyService Notes Fold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service Changere DE Pièces LES ET L’ENTRETIEN Degrés MAX Dentretien Remarques Autorisé Garantie cette de exclus sont normal l’entretien etInitiale d’achat date la de compter à jours 90 dix Connexions les et interrupteurs les câblage, le Vérifiez Dépannage DE GuideLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage Carburateur LE Régler Pour Starter DU Commande LA Régler PourGAZ DES Commande Reglages ET Revision28 .FIG Fig la Voir Tionsraparé LES Pour Roues LES Enlever PourAvant Roue LA DE PINCEMENT/CARROSSAGE 29 .FIGTondeuse DE Lame DE Mentnetraî Réglages ET RévisionFig la Voir D’ENTRAÎNEMENT Courroie LA Remplacer Pour FIG LA Voir23 .FIG Tondeuse LA Niveau LE Ajuster Pour25 .FIG 24 .FIGPlace en bien est courroie la que vous-Assurez Important 21 .FIG 19 .FIG20 .FIG 18 .FIG17.FIG Courroie LA ET Tondeuse LA InstallerFig Voir Tondeuse LA Enlever PourMoteur DE D’HUILE Filtre EntretienFig la Voir ’ALLUMAGE BougieTransmission LA DE Refroidissement AIR À Filtre’AIR Tamis LE Nettoyer Sionmistrans LA DE Moteur FluideEN Fonctionnement DE Système ET Fig la Voir Lame LA EnleverUtilisation Chaque Avant Lubrification DE Tableau12 .FIG Avant ET Réinstallation LA Après Purgée ÊtreUtilisation Transmission LA PurgerMoteur DU D’HUILE Niveau LE Vérifier E T O MO P ’ESSENCE Réservoir LE RemplirAccessoires Autres ET Charrettes DES Remorquer Pour 11 et 3 .Fig les VoirMAR EN Fonctionnement DE Système Fig la Tondeuse LA Utiliser PourVitess DE Régulateur LE Utiliser CommentFig la Voir Arrêter Pour 4 .FIG GAZ DES Commande LA Utiliser PourS I L I T U Fig la Voir Mentnetionsta DE Frein LE Engager PourMoteur de vitesse la commander de permet GAZ DES Commande D Froid moteur un démarrer de permet Détrangleur Commande’EMBRAYAGE PA LA DE Tracteur LE Retirer Pour MontageDesmancom des tionfonc la et Tionsec la Voir Conduisant LE EN TeletMontées NON Piéces Toncar DU Tracteur LE Sortir PourR E T T a B I F I R É Sommaire ’ESSENCE DE Sûre Manipulation Général EntretienTracteurs des sécurité toute En l’utilisation pour ConseilsPentes LES Dans FonctionnementTracteurs des sécurité toute en l’utilisation pour Conseils AUX Imprimé

96042004900, 412523 specifications

The Poulan 412523,96042004900 is a versatile and efficient chainsaw designed for both homeowners and professionals seeking reliable performance for various cutting tasks. Whether it's trimming branches, felling small trees, or tackling firewood, this chainsaw is equipped to handle a range of applications with ease.

One of the main features of the Poulan 412523 is its powerful engine, which typically provides a high power-to-weight ratio, allowing for efficient cutting while minimizing user fatigue. The chainsaw's engine design ensures smooth operation and quick starts, making it a user-friendly tool for both experienced users and novices. Its lightweight frame contributes to its maneuverability, making it easier to handle during extended use.

The chainsaw is equipped with a quality bar and chain that delivers excellent cutting performance. The chain's design ensures optimal cutting efficiency while being able to withstand significant wear, which is essential for heavy-duty tasks. The bar length is designed to handle various cutting depths, allowing users to make precise cuts as needed.

Safety is a paramount concern with any chainsaw, and the Poulan 412523 addresses this with several integrated safety features. These include a chain brake, which quickly stops the chain upon sudden release, and a safety throttle that prevents accidental engagement. Moreover, the ergonomic handle design offers a secure grip, reducing the risk of slippage while cutting.

Technology-wise, this chainsaw incorporates an efficient fuel system that promotes better fuel economy and lower emissions. This is particularly important in today’s environmental landscape, as operators seek to minimize their carbon footprint while working with power tools. Additionally, the Poulan 412523 features an easy-access air filter, which simplifies maintenance and ensures optimal engine performance by keeping dirt and debris at bay.

Another standout characteristic of this chainsaw is its durability. Made with robust materials, the Poulan 412523 is built to withstand harsh working conditions, ensuring a long lifespan. Coupled with regular maintenance, users can expect a reliable performance over many seasons.

In conclusion, the Poulan 412523,96042004900 is a well-rounded chainsaw offering a blend of power, safety, and user-friendly features. With its smart design and advanced technologies, it is suitable for various cutting tasks and is a valuable addition to any toolkit, whether for professional landscapers or enthusiastic homeowners.
Top Page Image Contents