Poulan 412412 manual Tractor, Brake Operation, Tires, Blade Care, Battery

Page 15

MAINTENANCE

TRACTOR

Always observe safety rules when performing any main- tenance.

BRAKE OPERATION

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual).

TIRES

•Maintain proper air pressure in all tires (See PSI on tires).

•Keep tires free of gasoline, oil, or insect control chemi- cals which can harm rubber.

•Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

OPERATOR PRESENCE SYSTEM AND REVERSE OP- ERATION SYSTEM (ROS)

Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately.

•The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position.

CHECK OPERATOR PRESENCE SYSTEM

•When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine.

•When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine.

•The attachment clutch should never operate unless the operator is in the seat.

ROS "ON" Position

Engine "ON" Position

(Normal Operating)

 

02828

CHECK REVERSE OPERATION (ROS) SYSTEM

•When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine.

•When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch en- gaged, any attempt by the operator to shift into reverse should NOT shut off the engine.

BLADE CARE

For best results mower blades must be sharp. Replace worn, bent or damaged blades.

CAUTION: Useonlyareplacementblade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty.

BLADE REMOVAL (See Fig. 13)

•Raise mower to highest position to allow access to blades.

NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth.

•Remove blade bolt by turning counterclockwise.

•Install new blade with stamped "GRASS SIDE" facing the ground.

IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly.

•Install and tighten blade bolt securely (45-55 Ft. Lbs. torque).

IMPORTANT: Special blade bolt is heat treated.

BLADE

 

 

MANDREL

 

 

 

ASSEMBLY

 

CENTER

 

 

 

HOLE

 

 

BLADE BOLT

 

 

 

(SPECIAL)

0

2

544

 

 

 

 

 

 

 

 

 

STAR

FIG. 13

BATTERY

Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Remove terminal guard.

•Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Model XT20H46YTII. Slope Operation Safety RulesSafe Operation Practices for Ride-On Mowers General OperationService III. ChildrenIV. Towing Table of Contents Unpack Carton AssemblyUnassembled Parts To Remove Tractor from CartonCheck Brake System Check Tire PressureCheck Deck Levelness Check for Proper Position of ALL BeltsOperation Know Your Tractor Stopping HOW to USE Your TractorTo Operate Mower To Adjust Mower Cutting Height See FigTo Adjust Gauge Wheels See Fig System CharacteristicsTo Transport See Figs Before Starting the EngineReverse Operation System ROS To Operate on HillsAutomatic Transmission Warm UP ADD GasolineTo Start Engine See Fig Purge TransmissionMowing Tips Schedule MaintenanceMaintenance General RecommendationsTires BatteryTractor Brake OperationEngine Spark Plugs CleaningEngine OIL Filter MufflerService and Adjustments To Install Mower See -21To Remove Mower See Fig Install belt on engine pulley M, in belt keepers G To Level Mower To Replace Mower Drive Belt See Fig To Check BrakeTo Replace Motion Drive Belt See Fig To Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Fig Front Wheel TOE-IN/CAMBERTo Replace Headlight Bulb To Adjust Throttle Control CableTo Adjust Choke Control To Adjust CarburetorEngine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsEngine dies when Fold Along This Dotted Line Degree Slope Only Ride UP and Down Hill Not Across Hill Degrees MAXLimited Warranty Service Notes Service Notes Service Notes Parts and Service Changere DE Pièces LES ET L’ENTRETIEN Dentretien Remarques Dentretien Remarques Dentretien Remarques Limitée Garantie UNE Pliez EST Ceci Degrés Suivant LESConnexions les et interrupteurs les câblage, le Vérifiez Dépannage DE GuideLame de mandrin le Remplacez Tordu est lame de mandrin Un Entreposage Moteur Starter DU Commande LA Régler PourGAZ DES Commande LA DE Câble LE Régler Pour Reglages ET RevisionFig la Voir Batterie LA Replacer Fig la Voir Tionsraparé LES Pour Roues LES Enlever PourAvant Roue LA DE PINCEMENT/CARROSSAGE 27 .FIG Réglages ET RévisionFig la Voir D’ENTRAÎNEMENT Courroie a L Acer Rempl Pour Freins LES Vérifier Pour23 .FIG Tondeuse LA Niveau LE Ajuster Pour25 .FIG 24 .FIG21 .FIG 19 .FIG 20 .FIG18 .FIG 17 .FIG Courroie LA ET Tondeuse LA InstallerFig Voir Tondeuse LA Enlever PourMoteur DE D’HUILE Filtre EntretienFig la Voir ’ALLUMAGE BougieTransmission LA DE Refroidissement AIR À Filtre’AIR Tamis LE Nettoyer Sionmistrans LA DE Moteur FluideEN Fonctionnement DE Système ET Fig la Voir Lame LA EnleverUtilisation Chaque Avant Lubrification DE Tableau12 .FIG UtilisationSion Transmis DE Réchauffement Transmission LA PurgerMoteur LE Démarrer Pour QuetimaautoMAR EN Fonctionnement DE Système 11 et 3 .Fig les VoirSystème DU Caractéristiques Tondeuse LA Utiliser PourJauge DE Roues LES Régler Pour 10 .FIGFig la Voir Mentnetionsta DE Frein LE Engager Pour GAZ DES Commande LA Utiliser PourVitess DE Régulateur LE Utiliser CommentUtilisation ’EMBRAYAGE Montage Desmancom des tionfonc la etLA DE Tracteur LE Retirer Pour Fig la Voir Siège LE Ajustez Montées NON PiécesToncar DU Tracteur LE Sortir Pour Fig la Voir Batterie LA VérifierSommaire ’ESSENCE DE Sûre Manipulation Général EntretienTracteurs des sécurité toute En l’utilisation pour ConseilsPentes LES Dans FonctionnementTracteurs des sécurité toute en l’utilisation pour Conseils AUX Imprimé

412412 specifications

The Poulan 412412 is a noteworthy chainsaw that combines power, efficiency, and user-friendly design, making it a popular choice for both hobbyists and professionals alike. Known for its versatility, the Poulan 412412 excels at a variety of tasks such as tree pruning, firewood cutting, and other general outdoor applications.

One of the standout features of the Poulan 412412 is its robust engine. Equipped with a reliable two-stroke engine, it delivers substantial power for its size. The engine ensures smooth operation and effective performance, allowing users to tackle even tough cutting tasks with ease. The saw is lightweight, which significantly enhances maneuverability and reduces user fatigue, enabling longer working sessions without discomfort.

The Poulan 412412 also boasts an efficient cutting system. It is fitted with a high-quality bar and chain that work in unison to ensure a clean and precise cut. The 16-inch bar length strikes a perfect balance between agility and cutting capacity, allowing users to handle a variety of cutting tasks without the need for a larger, heavier model.

Innovative technologies enhance the overall performance and safety of the Poulan 412412. The chainsaw features an automatic oiler system that delivers lubrication to the chain, minimizing wear and extending the lifespan of the chain and bar. Safety features such as a chain brake and anti-vibration technology ensure that users can operate the saw with confidence, even during extended periods of use.

Ease of maintenance is another key characteristic of the Poulan 412412. Access to the air filter and spark plug is straightforward, allowing users to perform routine maintenance without the need for specialized tools. This accessibility promotes regular upkeep, ensuring that the chainsaw remains in optimal working condition for years to come.

In conclusion, the Poulan 412412 is a reliable and efficient chainsaw that stands out due to its powerful engine, effective cutting system, and user-friendly design. With its commitment to safety and easy maintenance, it is an excellent choice for anyone looking to get the most out of their outdoor power equipment. Whether you are a seasoned professional or a budding DIY enthusiast, the Poulan 412412 is designed to meet your cutting needs with precision and reliability.
Top Page Image Contents