Poulan PB2042YT, 430097 manual To Operate Mower, To Stop Mower Blades, Reverse Operation System ROS

OPERATION

TO ADJUST MOWER CUTTING HEIGHT (See Fig. 9)

The position of the attachment lift lever (A) determines the cutting height.

A

Fig. 9

•Put attachment lift lever in desired cutting height slot.

The cutting height range is approximately 1" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2" during the cool season and to over 3" during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6" in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO OPERATE MOWER

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine. You must remain fully and centrally positioned in the seat to prevent the engine from hesitat- ing or cutting off when operating your equipment on rough, rolling terrain or hills.

•Select desired height of cut with attachment lift lever.

•Start mower blades by engaging attachment clutch control.

TO STOP MOWER BLADES

•Disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped, or the deflector shield (S) in place (See Fig. 10).

S

Fig. 10 10

REVERSE OPERATION SYSTEM (ROS)

Your tractor is equipped with a Reverse Operation System (ROS). Any attempt by the operator to travel in the reverse direction with the attachment clutch engaged will shut off the engine unless ignition key is placed in the ROS "ON" position.

WARNING: Backing up with the attachment clutch en- gaged while mowing is strongly discouraged. Turning the ROS "ON", to allow reverse operation with the attachment clutch engaged, should only be done when the operator decides it is necessary to reposition the machine with the attachment engaged. Do not mow in reverse unless absolutely necessary.

USING THE REVERSE OPERATION SYSTEM -

•Depress clutch/brake pedal all the way down and hold.

•With engine running, turn ignition key counterclockwise to ROS "ON" position.

•Look down and behind before backing.

•Move gear shift lever to reverse (R) position and slowly release clutch/brake pedal to start movement.

•When use of the ROS is no longer needed, turn the ignition key clockwise to engine "ON" position.

	8
ROS "ON" POSITION	0282
	ENGINE "ON" POSITION
	(NORMAL OPERATING)

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choosetheslowestspeed beforestartingupordownhills.

•Avoid stopping or changing speed on hills.

•If stopping is absolutely necessary, push clutch/brake pedal quickly to brake position and engage parking brake.

•Movegearshift leverto1stgear. Besureyouhaveallowed room for tractor to roll slightly as you restart movement.

•To restart movement, slowly release parking brake and clutch/brake pedal.

•Make all turns slowly.

TO TRANSPORT

•Raise attachment lift to highest position with attachment lift control.

•When pushing or towing your tractor, be sure gearshift lever is in neutral (N) position.

•Do not push or tow tractor at more than five (5) MPH.

NOTE: To protect hood from damage when transporting your tractor on a truck or a trailer, be sure hood is closed and secured to tractor. Use an appropriate means of tying hood to tractor (rope, cord, etc.).

TOWING CARTS AND OTHER ATTACHMENTS

Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your trac- tor. Use common sense when towing. Too heavy of a load, while on a slope, is dangerous. Tires can lose traction with the ground and cause you to lose control of your tractor.