Poulan 185498 To Adjust Gauge Wheels See Fig, To Operate Mower See Fig, To Operate on Hills

Page 13

OPERATION

The cutting height range is approximately 1-1/2" to 4". The heights are measured from the ground to the blade tip with the engine not running. These heights are approximate and may vary depending upon soil conditions, height of grass and types of grass being mowed.

•The average lawn should be cut to approximately 2-1/2 inches during the cool season and to over 3 inches during hot months. For healthier and better looking lawns, mow often and after moderate growth.

•For best cutting performance, grass over 6 inches in height should be mowed twice. Make the first cut relatively high; the second to desired height.

TO ADJUST GAUGE WHEELS (See Fig. 9)

Gauge wheels are properly adjusted when they are slightly off the ground when mower is at the desired cutting height in operating position. Gauge wheels then keep the deck in proper position to help prevent scalping in most terrain conditions.

NOTE:Adjust gauge wheels with tractor on a flat level surface.

•Adjust mower to desired cutting height (See “TO AD- JUST MOWER CUTTING HEIGHT” in the Operation section of this manual).

•Remove retainer spring and clevis pin which secure each gauge wheel bar.

•Lower gauge wheels to ground. Raise gauge wheels slightly to align holes in bracket and gauge wheel bar and insert clevis pin. Gauge wheels should be slightly off the ground.

•Replace retainer spring into clevis pin.

•Be sure all gauge wheels are in the same setting.

IMPORTANT:BE SURETO READJUST GAUGEWHEELS IFYOU CHANGE THE CUTTING HEIGHT OF THE MOWER DECK.

RETAINER

SPRING

019

77

 

CLEVIS

PIN

FIG. 9

TO OPERATE MOWER (See Fig. 10)

Your tractor is equipped with an operator presence sensing switch. Any attempt by the operator to leave the seat with the engine running and the attachment clutch engaged will shut off the engine.

•Select desired height of cut.

•Lower mower with attachment lift control.

•Start mower blades by engaging attachment clutch

control.

•TO STOP MOWER BLADES - disengage attachment clutch control.

CAUTION: Do not operate the mower without either the entire grass catcher, on mowers so equipped,or the deflector shield in place.

PULL OUT TO

ATTACHMENT LIFT LEVER HIGH POSITION

"ENGAGE"

 

 

 

 

LOW

 

 

POSITION

ATTACHMENT

 

 

CLUTCH SWITCH

 

 

PUSH IN TO

 

 

"DISENGAGED"

 

 

DEFLECTOR SHIELD

02142

 

FIG. 10

TO OPERATE ON HILLS

WARNING: Do not drive up or down hills with slopes greater than 15° and do not drive across any slope.

•Choose the slowest speed before starting up or down hills.

•Avoid stopping or changing speed on hills.

•If stopping is absolutely necessary, push brake pedal quickly to brake position and engage parking brake.

•To restart movement, slowly release parking brake and brake pedal.

•Slowly depress appropriate drive pedal to slowest set- ting.

•Make all turns slowly.

TO TRANSPORT (See Figs. 7 and 11)

When pushing or towing your tractor, be sure to disengage transmission by placing freewheel control in freewheeling position. Free wheel control is located at the rear drawbar of tractor.

•Raise attachment lift to highest position with attachment lift control.

•Pull freewheel control out and into the slot and release so it is held in the disengaged position.

•Do not push or tow tractor at more than two (2) MPH.

•To reengage transmission, reverse above procedure.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents PD20PH48STA Safety Rules Safety Rules Table of Contents Steering Wheel Gauge Wheels Unassembled PartsSeat Nose Roller MowerTools Required for Assembly AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigTo Attach Nose Roller See Fig Install Mower and Drive Belt See FigsCheck Mower Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigTo Operate on Hills To Transport See FigsTowing Carts and Other ATTACH- Ments Before Starting the EngineCheck Engine OIL Level ADD GasolineMowing Tips Purge TransmissionAutomatic Transmission Warm UP Lubrication Chart MaintenanceGeneral Recommendations Before Each USETractor Engine Clean AIR INTAKE/COOLING Areas CleaningMuffler Spark PlugsTo Install Mower Service and AdjustmentsTo Remove Mower See Fig To Replace Mower Drive Belt To Level Mower HousingTo Replace Mower Blade Secondary Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Steering Wheel ALIGN- Ment Transmission REMOVAL/REPLACEMENTTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Remove Wheel for Repairs See Fig To Replace Headlight BulbInterlocks and Relays To Adjust CarburetorTo Replace Fuse Other StorageFuel System Engine OILProblem Cause Correction Troubleshooting PointsWith attachment clutch Tractor Model Number PD20PH48STA, Product Number 954 56 SchematicElectrical KEY Part Description Chassis and Enclosures Repair Parts Tractor Model Number PD20PH48STA, Product Number 954 56 KEY Part NO. NO. Description DriveSteering Assembly 180656 Wheel Steering Engine Stem Tank Fuel Seat Assembly Wheels & Tires DecalsMower Lift KEY Part NO. NO. Description Mower Deck 175820 Pulley Idler Flat Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service

185498, 954569516 specifications

The Poulan 185498 and 954569516 are noteworthy models within the Poulan brand, known for their reliability and efficiency in outdoor power equipment. As a trusted name in the industry, Poulan has designed these models to cater to both amateur and professional landscapers, showcasing advanced technologies and user-friendly features.

One of the primary features of the Poulan 185498 is its powerful engine, often equipped with a robust two-stroke design that delivers optimal performance for cutting and trimming tasks. This engine provides excellent power-to-weight ratio, enabling users to handle tough jobs with ease. The 954569516 model boasts similar engine specifications, designed to ensure a quick start and consistent power output, making it an ideal choice for various applications.

Both models incorporate innovative technologies to enhance user experience. For instance, the Easy Start technology assists users in starting their machines with minimal effort. This feature significantly reduces the amount of pull effort required, allowing even novice users to operate the equipment successfully. Additionally, vibration dampening features are integrated into both models, which minimize fatigue during extended use, ensuring comfort and better control.

Another characteristic that stands out is the blade and cutting system. The Poulan 185498 comes equipped with high-quality, durable blades that provide precise cuts, making it suitable for intricate landscaping work. Meanwhile, the 954569516 model features an adjustable cutting height system, allowing users to customize their cutting experience based on specific requirements.

The design of both models emphasizes durability and ease of maintenance. The tough exterior can withstand challenging outdoor conditions, ensuring longevity. Users will appreciate the tool-less maintenance features, allowing for quick blade changes and easy access to the air filter and spark plug, which can enhance the overall maintenance routine.

In conclusion, the Poulan 185498 and 954569516 models stand out for their powerful engines, user-friendly technologies, and durable construction. They embody the Poulan commitment to quality and performance, making them suitable for a wide range of landscaping tasks, from residential yards to commercial properties. Whether you are a seasoned professional or an enthusiastic DIYer, these models provide the reliability and efficiency needed to tackle any outdoor project with confidence.
Top Page Image Contents