Poulan 954569516, 185498 To Remove Wheel for Repairs See Fig, Replacing Battery See Fig

Page 24

SERVICE AND ADJUSTMENTS

TO REMOVE WHEEL FOR REPAIRS (See Fig. 28)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

02614

WEAK OR DEAD BATTERY FULLY CHARGED BATTERY

FIG. 29

REPLACING BATTERY (See Fig. 30)

WARNING: Do not short battery ter- minals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands,rings,etc.

Positive terminal must be connected first to prevent sparking from accidental

AXLE COVER

RETAINING RING

grounding.

• Lift hood to raised position.

•

Remove terminal guard.

•

Disconnect BLACK battery cable then RED battery

SQUARE KEY (REAR WHEEL ONLY)

00663

cable and carefully remove battery from tractor.

• Install new battery with terminals in same position as

FIG. 28

TO START ENGINE WITH A WEAK BATTERY (See Fig. 29)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

 

old battery.

•

Reinstall terminal guard.

• First connect RED battery cable to positive (+) battery

 

terminal with hex bolt and keps nut as shown. Tighten

 

securely.

• Connect BLACK grounding cable to negative (-) battery

 

terminal with remaining hex bolt and keps nut. Tighten

 

securely

•

Close terminal access doors.

•

Close hood.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

TERMINAL ACCESS DOOR

TERMINAL GUARD

KEPS NUT

02179

HEX

BOLT

POSITIVE (RED)

CABLE

NEGATIVE (BLACK)

CABLE

•Connect one end of the RED cable to the POSITIVE

(+)terminal of each battery(A-B), taking care not to short against tractor chassis.

•Connect one end of the BLACK cable to the NEGATIVE (-) terminal (C) of fully charged battery.

•Connect the other end of the BLACK cable (D) to good chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

FIG. 30

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents PD20PH48STA Safety Rules Safety Rules Table of Contents Unassembled Parts Steering Wheel Gauge WheelsSeat Nose Roller MowerAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs To Attach Nose Roller See FigCheck Tire Pressure Check Mower LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolinePurge Transmission Mowing TipsAutomatic Transmission Warm UP Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Engine Cleaning Clean AIR INTAKE/COOLING AreasMuffler Spark PlugsService and Adjustments To Install MowerTo Remove Mower See Fig To Level Mower Housing To Replace Mower Drive BeltTo Check and Adjust Brake See Fig To Replace Mower Blade Secondary Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig To Replace Headlight BulbTo Adjust Carburetor Interlocks and RelaysTo Replace Fuse Storage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionWith attachment clutch Schematic Tractor Model Number PD20PH48STA, Product Number 954 56Electrical KEY Part Description Chassis and Enclosures Repair Parts Tractor Model Number PD20PH48STA, Product Number 954 56 Drive KEY Part NO. NO. DescriptionSteering Assembly 180656 Wheel Steering Engine Stem Tank Fuel Seat Assembly Decals Wheels & TiresMower Lift KEY Part NO. NO. Description Mower Deck 175820 Pulley Idler Flat Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service

185498, 954569516 specifications

The Poulan 185498 and 954569516 are noteworthy models within the Poulan brand, known for their reliability and efficiency in outdoor power equipment. As a trusted name in the industry, Poulan has designed these models to cater to both amateur and professional landscapers, showcasing advanced technologies and user-friendly features.

One of the primary features of the Poulan 185498 is its powerful engine, often equipped with a robust two-stroke design that delivers optimal performance for cutting and trimming tasks. This engine provides excellent power-to-weight ratio, enabling users to handle tough jobs with ease. The 954569516 model boasts similar engine specifications, designed to ensure a quick start and consistent power output, making it an ideal choice for various applications.

Both models incorporate innovative technologies to enhance user experience. For instance, the Easy Start technology assists users in starting their machines with minimal effort. This feature significantly reduces the amount of pull effort required, allowing even novice users to operate the equipment successfully. Additionally, vibration dampening features are integrated into both models, which minimize fatigue during extended use, ensuring comfort and better control.

Another characteristic that stands out is the blade and cutting system. The Poulan 185498 comes equipped with high-quality, durable blades that provide precise cuts, making it suitable for intricate landscaping work. Meanwhile, the 954569516 model features an adjustable cutting height system, allowing users to customize their cutting experience based on specific requirements.

The design of both models emphasizes durability and ease of maintenance. The tough exterior can withstand challenging outdoor conditions, ensuring longevity. Users will appreciate the tool-less maintenance features, allowing for quick blade changes and easy access to the air filter and spark plug, which can enhance the overall maintenance routine.

In conclusion, the Poulan 185498 and 954569516 models stand out for their powerful engines, user-friendly technologies, and durable construction. They embody the Poulan commitment to quality and performance, making them suitable for a wide range of landscaping tasks, from residential yards to commercial properties. Whether you are a seasoned professional or an enthusiastic DIYer, these models provide the reliability and efficiency needed to tackle any outdoor project with confidence.
Top Page Image Contents