Poulan 954569516, 185498 Service and Adjustments, To Remove Mower See Fig, To Install Mower

Page 20

SERVICE AND ADJUSTMENTS

WARNING:TO AVOID SERIOUS INJURY, BEFORE PERFORMING ANY SERVICE OR ADJUSTMENTS:

•Depress brake pedal fully and set parking brake.

•Place attachment clutch in “DISENGAGED” position.

•Turn ignition key to “STOP” and remove key.

•Make sure the blades and all moving parts have completely stopped.

•Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug.

TRACTOR

TO REMOVE MOWER (See Fig. 19)

•Place attachment clutch in “DISENGAGED” position.

•If equipped, turn height adjustment knob to lowest setting.

•Lower mower to its lowest position.

•Disengage belt tension rod from lock bracket.

CAUTION: Rod is spring loaded. Have a tight grip on rod and release slowly.

•Remove retainer spring holding anti-swaybar to chassis bracket and disengage anti-swaybar from bracket.

•Remove four retainer springs from front plate assembly and remove plate.

•Remove retainer springs from suspension arms at deck and disengage arms from deck.

•Raise attachment lift to its highest position.

•Slide mower forward and remove belt from electric clutch pulley.

•Slide mower out from under right side of tractor.

TO INSTALL MOWER

Be sure tractor is on level surface and mower suspension arms are raised with attachment lift control. Engage park- ing brake.

•Swing anti-sway bar to left side of mower deck.

•Slide mower under tractor with deflector shield to right side of tractor.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

•If equipped, turn height adjustment knob counter- clockwise until it stops.

•Lower mower linkage with attachment lift control.

•Be sure belt tension rod is in disengaged position.

•Install belt into electric clutch pulley groove.

•Place the suspension arms on outward pointing deck pins. Retain with double loop retainer spring with loops up as shown.

•Install front plate assembly to tractor suspension brackets and retain with single loop retainer springs as shown.

•Position front plate assembly between front mower brackets. Raise deck and plate assembly to align holes and insert flanged pins. Secure pins with double loop retainer springs between the plate assembly and mower brackets.

NOTE: To assist in locating hole in flanged pin, the hole in pin is inline with notch on head of pin. If necessary, move mower side-to-side to give space between plate and mower brackets.

IMPORTANT: CHECK BELT FOR PROPER ROUTING IN ALL MOWER PULLEY GROOVES.

SUSPENSION ARMS

 

 

LOCK BRACKET

BELT TENSION ROD

 

 

(DISENGAGED POSITION)

FRONT

ELECTRIC CLUTCH PULLEY

 

FRONT PLATE

 

MOWER

 

BRACKET

ASSEMBLY

CHASSIS

 

SINGLE LOOP

BRACKET

 

 

RETAINER

 

 

 

 

SPRING

 

 

DOUBLE LOOP

 

 

RETAINER

 

 

SPRING

RETAINER

 

 

SPRING

 

FLANGED PIN

 

ANTI-SWAY

 

USE PLIERS FOR

BAR

DEFLECTOR

RETAINER SPRINGS

 

SHIELD

 

SUSPENSION ARMS

 

 

DOUBLE LOOP

 

 

RETAINER SPRINGS

 

LOOP UP

(Outward pointing

 

deck pins)

02565

 

 

 

FIG. 19

20

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PD20PH48STA Safety Rules Safety Rules Table of Contents Unassembled Parts Steering Wheel Gauge WheelsSeat Nose Roller MowerAssembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Assemble Gauge Wheels to Mower Deck See FigInstall Mower and Drive Belt See Figs To Attach Nose Roller See FigCheck Tire Pressure Check Mower LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineAutomatic Transmission Warm UP Purge TransmissionMowing Tips Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Engine Cleaning Clean AIR INTAKE/COOLING AreasMuffler Spark PlugsTo Remove Mower See Fig Service and AdjustmentsTo Install Mower To Level Mower Housing To Replace Mower Drive BeltTo Check and Adjust Brake See Fig To Replace Mower Blade Secondary Drive Belt See FigTransmission REMOVAL/REPLACEMENT To Adjust Steering Wheel ALIGN- MentTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERReplacing Battery See Fig To Start Engine with a Weak Battery See FigTo Remove Wheel for Repairs See Fig To Replace Headlight BulbTo Replace Fuse To Adjust CarburetorInterlocks and Relays Storage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionWith attachment clutch Schematic Tractor Model Number PD20PH48STA, Product Number 954 56Electrical KEY Part Description Chassis and Enclosures Repair Parts Tractor Model Number PD20PH48STA, Product Number 954 56 Drive KEY Part NO. NO. DescriptionSteering Assembly 180656 Wheel Steering Engine Stem Tank Fuel Seat Assembly Decals Wheels & TiresMower Lift KEY Part NO. NO. Description Mower Deck 175820 Pulley Idler Flat Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Parts and Service

185498, 954569516 specifications

The Poulan 185498 and 954569516 are noteworthy models within the Poulan brand, known for their reliability and efficiency in outdoor power equipment. As a trusted name in the industry, Poulan has designed these models to cater to both amateur and professional landscapers, showcasing advanced technologies and user-friendly features.

One of the primary features of the Poulan 185498 is its powerful engine, often equipped with a robust two-stroke design that delivers optimal performance for cutting and trimming tasks. This engine provides excellent power-to-weight ratio, enabling users to handle tough jobs with ease. The 954569516 model boasts similar engine specifications, designed to ensure a quick start and consistent power output, making it an ideal choice for various applications.

Both models incorporate innovative technologies to enhance user experience. For instance, the Easy Start technology assists users in starting their machines with minimal effort. This feature significantly reduces the amount of pull effort required, allowing even novice users to operate the equipment successfully. Additionally, vibration dampening features are integrated into both models, which minimize fatigue during extended use, ensuring comfort and better control.

Another characteristic that stands out is the blade and cutting system. The Poulan 185498 comes equipped with high-quality, durable blades that provide precise cuts, making it suitable for intricate landscaping work. Meanwhile, the 954569516 model features an adjustable cutting height system, allowing users to customize their cutting experience based on specific requirements.

The design of both models emphasizes durability and ease of maintenance. The tough exterior can withstand challenging outdoor conditions, ensuring longevity. Users will appreciate the tool-less maintenance features, allowing for quick blade changes and easy access to the air filter and spark plug, which can enhance the overall maintenance routine.

In conclusion, the Poulan 185498 and 954569516 models stand out for their powerful engines, user-friendly technologies, and durable construction. They embody the Poulan commitment to quality and performance, making them suitable for a wide range of landscaping tasks, from residential yards to commercial properties. Whether you are a seasoned professional or an enthusiastic DIYer, these models provide the reliability and efficiency needed to tackle any outdoor project with confidence.
Top Page Image Contents