Poulan 954567833 To Remove Wheel for Repairs See Fig, To Start Engine with a Weak Battery See Fig

Page 22

SERVICE AND ADJUSTMENTS

TO REMOVE WHEEL FOR REPAIRS (See Fig. 26)

•Block up axle securely.

•Remove axle cover, retaining ring and washers to allow wheel removal (rear wheel contains a square key - Do not lose).

•Repair tire and reassemble.

•On rear wheels only: align grooves in rear wheel hub and axle. Insert square key.

•Replace washers and snap retaining ring securely in axle groove.

•Replace axle cover.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

WASHERS

RETAINING

RING

AXLE

COVER

SQUARE KEY

00663

(REAR WHEEL ONLY)

FIG. 26

TO START ENGINE WITH A WEAK BATTERY (See Fig. 27)

WARNING: Lead-acid batteries gen- erate explosive gases. Keep sparks, flame and smoking materials away from batteries. Always wear eye protection when around batteries.

If your battery is too weak to start the engine, it should be recharged. (See "BATTERY" in the Maintenance section

 

02614

WEAK OR DEAD

FULLY CHARGED

BATTERY

BATTERY

FIG. 27

REPLACING BATTERY (See Fig. 28)

WARNING: Do not short battery ter- minals by allowing a wrench or any other object to contact both terminals at the same time. Before connecting battery, remove metal bracelets, wristwatch bands,rings,etc.

Positive terminal must be connected first to prevent sparking from accidental grounding.

•Lift hood to raised position.

•Remove terminal guard.

•Disconnect BLACK battery cable then RED battery cable and carefully remove battery from tractor.

•Install new battery with terminals in same position as old battery.

•Reinstall terminal guard.

•First connect RED battery cable to positive (+) battery terminal with hex bolt and keps nut as shown. Tighten securely.

•Connect BLACK grounding cable to negative (-) battery terminal with remaining hex bolt and keps nut. Tighten securely

•Close terminal access doors.

•Close hood.

of this manual).

If “jumper cables” are used for emergency starting, follow this procedure:

IMPORTANT: YOUR TRACTOR IS EQUIPPED WITH A 12 VOLT SYSTEM. THE OTHER VEHICLE MUST ALSO BE A 12 VOLT SYSTEM. DO NOT USE YOUR TRACTOR BATTERY TO START OTHER VEHICLES.

TO ATTACH JUMPER CABLES -

• Connect one end of the RED cable to the POSITIVE

(+) terminal of each battery(A-B), taking care not to

short against tractor chassis.

TERMINAL ACCESS DOOR

TERMINAL GUARD

KEPS NUT

02179

HEX

BOLT

POSITIVE (RED)

CABLE

NEGATIVE (BLACK)

CABLE

•

Connect one end of the BLACK cable to the NEGATIVE

 

(-) terminal (C) of fully charged battery.

•

Connect the other end of the BLACK cable (D) to good

 

chassis ground, away from fuel tank and battery.

TO REMOVE CABLES, REVERSE ORDER -

•BLACK cable first from chassis and then from the fully charged battery.

•RED cable last from both batteries.

FIG. 28

TO REPLACE HEADLIGHT BULB

•Raise hood.

•Pull bulb holder out of the hole in the backside of the grill.

•Replace bulb in holder and push bulb holder securely back into the hole in the backside of the grill.

•Close hood.

22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents PR20PH42STD Safety Rules Safety Rules Table of Contents Steering Wheel Seat Unassembled PartsSlope Sheet HOW to SET UP Your Tractor AssemblyTools Required for Assembly To Remove Tractor from CartonInstall Seat See Fig Assemble Gauge Wheels to Mower Deck See FigCheck Tire Pressure To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Mower LevelnessOperation Know Your Tractor To Move Forward and Backward HOW to USE Your TractorTo USE Cruise Control To Operate on Hills To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Transport See FigsCheck Engine OIL Level Before Starting the EngineTowing Carts and Other ATTACH- Ments ADD GasolineMowing Tips Purge TransmissionMulching Mowing Tips General Recommendations MaintenanceLubrication Chart Before Each USETractor Engine Muffler CleaningClean AIR INTAKE/COOLING Areas Spark PlugsTo Level Mower Housing Service and AdjustmentsTo Install Mower See Fig To Remove Mower See FigTo Replace Mower Blade Drive Belt See Fig To Check and Adjust Brake See FigBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig Transmission REMOVAL/EPLACEMENTTo Adjust Steering Wheel Alignment Front Wheel TOE-IN/CAMBERTo Remove Wheel for Repairs See Fig To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Replace Headlight BulbInterlocks and Relays To Adjust CarburetorTo Replace Fuse Fuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionWith attachment clutch PTO Switch SchematicIgnition Switch Wiring Insulated ClipsElectrical KEY Part Description Chassis and Enclosures Repair Parts Tractor Model Number PR20PH42STD, Product no 56 Drive KEY Part NO. NO. DescriptionSteering Assembly KEY Part Description Engine KEY Part NO. NO. Description Seat Assembly Decals Wheels & TiresMower Lift Repair Parts Mower Deck 182032X421 Service Notes Service Notes Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

186914, 954567833 specifications

The Poulan 954567833,186914 is a standout product in the realm of outdoor power equipment, particularly known for its powerful performance and innovative features. As a part of Poulan's extensive lineup, this model combines reliability with user-friendly features, making it an excellent choice for both amateur gardeners and professional landscapers alike.

One of the key characteristics of the Poulan 954567833,186914 is its robust engine. Designed for efficiency and endurance, the engine provides ample power to tackle various landscaping tasks, from trimming grass to cutting through thick bushes. The model features a high-performance 2-cycle engine, which not only enhances its cutting power but also ensures that the machine is lightweight and easy to handle. This results in less fatigue for users during extended periods of use.

Another noteworthy feature of this model is its ergonomic design. The Poulan 954567833,186914 is equipped with a lightweight body that allows for greater maneuverability, making it easier to navigate tight spaces in gardens and yards. The soft-grip handles provide comfort during operation, reducing vibrations and enabling users to maintain a secure grip while working.

In terms of technology, the Poulan 954567833,186914 incorporates an advanced air filtration system. This system helps keep the engine clean and reduces the frequency of maintenance required, leading to longer intervals between servicing. The easy-access air filter makes routine maintenance a breeze for users, promoting longevity and efficiency.

The model also features a quick-release trimmer head, allowing users to swap out different cutting attachments seamlessly. This versatility makes it suitable for a wide range of applications, whether you’re dealing with overgrown grass or fine trimming around flower beds.

Fuel efficiency is another highlight of the Poulan 954567833,186914. Designed to be environmentally conscious, this model minimizes fuel consumption while maximizing power output. This not only saves on operational costs but also contributes to reduced emissions, aligning with modern sustainability practices.

In summary, the Poulan 954567833,186914 is a well-engineered outdoor power equipment choice that excels in performance, comfort, and environmental efficiency. With its powerful engine, ergonomic design, advanced technologies, and ease of use, it stands out as a reliable tool for all your landscaping needs.
Top Page Image Contents