Poulan 186914, 954567833 Install Seat See Fig, Assemble Gauge Wheels to Mower Deck See Fig

Page 7

ASSEMBLY

INSTALL SEAT (See Fig. 3)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and flat washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and flat washer loosely. Do not tighten.

Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

SEAT

SEAT PAN

SHOULDER

BOLT

02466

FLAT WASHER

ADJUSTMENT

02464

KNOB

 

FIG. 3

NOTE: You may now roll or drive your tractor off the skid. Follow the appropriate instruction below to remove the tractor from the skid.

TO ROLL TRACTOR OFF SKID (See Op- eration section for location and function of controls)

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Release parking brake by depressing brake pedal.

•Place freewheel control in "transmission disengaged position" (See “TO TRANSPORT” in the Operation section of this manual).

•Roll tractor forward off skid.

•Remove banding holding the deflector shield up against

tractor.

TO DRIVE TRACTOR OFF SKID (See Op- eration section for location and function of controls)

WARNING: Before starting, read, understand and follow all instructions in the Operation section of this manual. Be sure tractor is in a well-ventilated area. Be sure the area in front of tractor is clear of other people and objects.

•Be sure all the above assembly steps have been com- pleted.

•Check engine oil level and fill fuel tank with gasoline.

•Place freewheel control in "transmission engaged" position (see "TO TRANSPORT" in Operation section of this manual).

•Sit on seat in operating position, depress brake pedal and set the parking brake.

•Place motion control lever in neutral (N) position.

•Press lift lever plunger and raise attachment lift lever to its highest position.

•Start the engine.After engine has started, move throttle control to idle position.

•Release parking brake.

•Slowly move the motion control lever forward and slowly drive tractor off skid.

•Apply brake to stop tractor, set parking brake and place motion control lever in neutral position.

•Turn ignition key to "STOP" position.

Continue with the instructions that follow.

ASSEMBLE GAUGE WHEELS TO MOWER DECK (See Fig. 4)

The gauge wheels are designed to keep the mower deck in proper position when operating mower. Be sure they are properly adjusted to ensure optimum mower perfor-

mance.

•Slide gauge wheel bar down into bracket channel, Be sure that gauge wheel bar aligning holes are on top. Assemble gauge wheels as shown using shoulder bolts, 3/8 washers and 3/8-16 center locknuts and tighten securely.

•Adjust gauge wheels before operating mower. See “TO ADJUST GAUGE WHEELS” in the Operation section of this manual.

RETAINER SPRING

PIN

SHOULDER

BOLT

ADJUSTING

BAR

02115

GAUGE

WHEEL

 

3/8-16 CENTER

3/8 WASHER

LOCKNUT

FIG. 4

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents PR20PH42STD Safety Rules Safety Rules Table of Contents Steering Wheel Seat Unassembled PartsSlope Sheet To Remove Tractor from Carton AssemblyTools Required for Assembly HOW to SET UP Your TractorAssemble Gauge Wheels to Mower Deck See Fig Install Seat See FigCheck Mower Levelness To SET UP Your Mower for MulchingTo Convert to Bagging or Discharging Check Tire PressureOperation Know Your Tractor To Move Forward and Backward HOW to USE Your TractorTo USE Cruise Control To Transport See Figs To Adjust Gauge Wheels See FigTo Operate Mower See Fig To Operate on HillsADD Gasoline Before Starting the EngineTowing Carts and Other ATTACH- Ments Check Engine OIL LevelMowing Tips Purge TransmissionMulching Mowing Tips Before Each USE MaintenanceLubrication Chart General RecommendationsTractor Engine Spark Plugs CleaningClean AIR INTAKE/COOLING Areas MufflerTo Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower HousingBelt Removal To Check and Adjust Brake See FigBelt Installation To Replace Mower Blade Drive Belt See FigFront Wheel TOE-IN/CAMBER Transmission REMOVAL/EPLACEMENTTo Adjust Steering Wheel Alignment To Replace Motion Drive Belt See FigTo Replace Headlight Bulb To Start Engine with a Weak Battery See FigReplacing Battery See Fig To Remove Wheel for Repairs See FigInterlocks and Relays To Adjust CarburetorTo Replace Fuse Engine OIL StorageOther Fuel SystemProblem Cause Correction Troubleshooting PointsWith attachment clutch Wiring Insulated Clips SchematicIgnition Switch PTO SwitchElectrical KEY Part Description Chassis and Enclosures Repair Parts Tractor Model Number PR20PH42STD, Product no 56 KEY Part NO. NO. Description DriveSteering Assembly KEY Part Description Engine KEY Part NO. NO. Description Seat Assembly Wheels & Tires DecalsMower Lift Repair Parts Mower Deck 182032X421 Service Notes Service Notes Limited Warranty Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

186914, 954567833 specifications

The Poulan 954567833,186914 is a standout product in the realm of outdoor power equipment, particularly known for its powerful performance and innovative features. As a part of Poulan's extensive lineup, this model combines reliability with user-friendly features, making it an excellent choice for both amateur gardeners and professional landscapers alike.

One of the key characteristics of the Poulan 954567833,186914 is its robust engine. Designed for efficiency and endurance, the engine provides ample power to tackle various landscaping tasks, from trimming grass to cutting through thick bushes. The model features a high-performance 2-cycle engine, which not only enhances its cutting power but also ensures that the machine is lightweight and easy to handle. This results in less fatigue for users during extended periods of use.

Another noteworthy feature of this model is its ergonomic design. The Poulan 954567833,186914 is equipped with a lightweight body that allows for greater maneuverability, making it easier to navigate tight spaces in gardens and yards. The soft-grip handles provide comfort during operation, reducing vibrations and enabling users to maintain a secure grip while working.

In terms of technology, the Poulan 954567833,186914 incorporates an advanced air filtration system. This system helps keep the engine clean and reduces the frequency of maintenance required, leading to longer intervals between servicing. The easy-access air filter makes routine maintenance a breeze for users, promoting longevity and efficiency.

The model also features a quick-release trimmer head, allowing users to swap out different cutting attachments seamlessly. This versatility makes it suitable for a wide range of applications, whether you’re dealing with overgrown grass or fine trimming around flower beds.

Fuel efficiency is another highlight of the Poulan 954567833,186914. Designed to be environmentally conscious, this model minimizes fuel consumption while maximizing power output. This not only saves on operational costs but also contributes to reduced emissions, aligning with modern sustainability practices.

In summary, the Poulan 954567833,186914 is a well-engineered outdoor power equipment choice that excels in performance, comfort, and environmental efficiency. With its powerful engine, ergonomic design, advanced technologies, and ease of use, it stands out as a reliable tool for all your landscaping needs.
Top Page Image Contents