INSTALLATION
LISTED COMPONENTS
FOR MOBILE HOME
INSTALLATION
The Regency Small, Medium, Medium Step and Large Freestanding pedestal units are ap- proved for installation in a Mobile Home if one of the following pipe systems is used.
U.S. Installation*
METALBESTOS SSII
Qty. Part # | Description |
1 | Connector Kit |
SIMPSON
Qty.Part # | Description | |
1 | 6DVL8693 | Connector Kit |
1 | ||
ICC EXCEL 2100 | ||
Qty.Part # | Description | |
1 | 6CL48 | 48" Chimney length (also in 12", |
|
| 18", 24" lengths. |
1 | 6RC | Rain Cap |
1 | 6RCS | Spark Screen (for rain cap) |
1 | 6RDS/SQS | Round/Square support box |
1 | 6VF | Flashing |
1 | 6UBA | "Ultrablack" Close Clearance |
|
| Connector |
Large Stoves F3100L and S3100L
The unit arrives with the first two air tubes (from the front) and the 2 baffle bricks on the floor of the firebox. The baffle bricks are positioned first and then the air tubes are installed.
NOTE: If the first 2 airtubes are already installed in the stove, they must be removed in order to install the Brick Baffles.
1)Slide the left baffle brick over the two rear air tubes and then push it all the way to the left side of the firebox.
1 | 6TMH | Shield/Support |
1 | Flashing | |
1 | Chimney Length | |
1 | Chimney Length | |
1 | Rain Cap | |
|
| |
Qty.Part # | Description | |
1 | Connector | |
1 | CSB | Shield/Support |
1 | RRS | Radiation Shield |
1 | LFR03 | Flashing |
1 | SL3 | Chimney Length |
1 | SL1 | Chimney Length |
1 | RCSA | Rain Cap |
SECURITY ASHT | ||
Qty.Part # | Description | |
1 | Connector Kit | |
1 | 6SS | Shield/Support |
1 | 6FAMH | Flashing |
1 | 6L3 | Chimney Length |
1 | 6L1 | Chimney Length |
1 | CPE | Rain Cap |
SECURITY S2100 | ||
Qty.Part # | Description | |
1 | Connector Kit | |
1 | 6XSF | Support |
Canadian Installations*
SECURITY S2100 (see above for details)
ICC EXCEL 2100 (see above for details)
*The use of alternate pitch flashings, support box extensions, additional chimney lengths, and additional chimney bracing, may be used on each of the previously listed systems. These parts though must be from the same system as listed, and must be a similar and/or complimen- tary part.
CAUTION: At no time use unlabelled parts, or substitute parts made for another chimney system.
Install as per chimney manufacturer's installa- tion instructions.
BRICK FLUE BAFFLE & SECONDARY AIR TUBE INSTALLATION
Side View
2)Tilt the first Baffle Brick down and then slide the 2nd Baffle Brick up and back. Reposi- tion both baffle bricks flat on the air tubes.
1 | 6XFA | Flashing |
1 | 6XL3 | Chimney Length |
1 | 6XL18 | Chimney Length |
1 | 6XCPE | Rain Cap |
| ||
Qty.Part # | Description | |
1 | 6DWBK | Connector |
1 | 6TGRS | Roof Support |
1 | 6TGG36 | Chimney Length |
1 | 6TGG12 | Chimney Length |
1 | 6TGF | Flashing |
1 | 6TGC | Rain Cap |
|
| |
Qty.Part # | Description | |
1 | 6DCC | Connector |
1 | Roof Support | |
1 | 6F | Flashing |
1 |
| Chimney Length |
1 |
| Chimney Length |
The flue baffle system located in the upper area of the firebox is removable to make cleaning your chimney system easier. The brick baffles must be installed prior to your first fire. Smoke spillage and draft problems may occur if the baffles are improperly positioned. Check the position of the brick baffles on a regular basis as they can be dislodged if too much fuel is forced into the firebox.
The Large Stoves F3100L and S3100L are shipped with two of the secondary air tubes loose inside the firebox. They need to be in- stalled after the brick baffle are installed. Follow the directions below.
3)Important: push both baffle bricks so they are tight against the side walls.
1 |
Front View
Regency Freestanding Woodstove | 15 |
