Poulan 954567833 To Replace Mower Blade Drive Belt See Fig, To Check and Adjust Brake See Fig

Page 20

SERVICE AND ADJUSTMENTS

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

•Recheck measurements after adjusting.

BOTTOM EDGE OF MOWER

BOTTOM EDGE OF MOWER

TO GROUND

00598

TO GROUND

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

01267

A

GROUND LINE

A

FIG. 19

SUSPENSION

ARM

01553

LIFT LINK

ADJUSTMENT NUT

FIG. 20

FRONT-TO-BACK ADJUSTMENT (See Figs. 21 and 22)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

•Before making any necessary adjustments, check that both front links are equal in length.

•If links are not equal in length, adjust one link to same length as other link.

•To lower front of mower loosen nut “E” on both front links an equal number of turns.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

•To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

•When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

•Recheck side-to-side adjustment.

01268

MANDREL

“D”“D”

FIG. 21

NUT “E”

NUT “F”

TRUNNION

FRONT LINKS

FIG. 22

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 23)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

•Remove mower from tractor (See “TO REMOVE MOWER” in this section of manual).

•Work belt off both mandrel pulleys and idler pulleys.

•Pull belt away from mower.

BELT INSTALLATION -

•Work belt around both mandrel pulleys and idler pulleys.

•Make sure belt is in all pulley grooves and inside all belt guides.

•Install mower (See "To Install Mower" in this section of manual).

MANDREL PULLEY IDLER

PULLEYS

MANDREL

PULLEY

FIG. 23

TO CHECK AND ADJUST BRAKE (See Fig. 24)

Your tractor is equipped with an adjustable brake system which is mounted on the right side of the transaxle.

If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved

20surface, then brake must be checked and adjusted.

Page 19 Page 21
Image 20
Page 19 Page 21
Contents PR20PH42STD Safety Rules Safety Rules Table of Contents Slope Sheet Unassembled PartsSteering Wheel Seat Assembly Tools Required for AssemblyHOW to SET UP Your Tractor To Remove Tractor from CartonInstall Seat See Fig Assemble Gauge Wheels to Mower Deck See FigTo SET UP Your Mower for Mulching To Convert to Bagging or DischargingCheck Tire Pressure Check Mower LevelnessOperation Know Your Tractor To USE Cruise Control HOW to USE Your TractorTo Move Forward and Backward To Adjust Gauge Wheels See Fig To Operate Mower See FigTo Operate on Hills To Transport See FigsBefore Starting the Engine Towing Carts and Other ATTACH- MentsCheck Engine OIL Level ADD GasolineMulching Mowing Tips Purge TransmissionMowing Tips Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Engine Cleaning Clean AIR INTAKE/COOLING AreasMuffler Spark PlugsService and Adjustments To Install Mower See FigTo Level Mower Housing To Remove Mower See FigTo Check and Adjust Brake See Fig Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTransmission REMOVAL/EPLACEMENT To Adjust Steering Wheel AlignmentTo Replace Motion Drive Belt See Fig Front Wheel TOE-IN/CAMBERTo Start Engine with a Weak Battery See Fig Replacing Battery See FigTo Remove Wheel for Repairs See Fig To Replace Headlight BulbTo Replace Fuse To Adjust CarburetorInterlocks and Relays Storage OtherFuel System Engine OILTroubleshooting Points Problem Cause CorrectionWith attachment clutch Schematic Ignition SwitchPTO Switch Wiring Insulated ClipsElectrical KEY Part Description Chassis and Enclosures Repair Parts Tractor Model Number PR20PH42STD, Product no 56 Drive KEY Part NO. NO. DescriptionSteering Assembly KEY Part Description Engine KEY Part NO. NO. Description Seat Assembly Decals Wheels & TiresMower Lift Repair Parts Mower Deck 182032X421 Service Notes Service Notes Limited Warranty Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

186914, 954567833 specifications

The Poulan 954567833,186914 is a standout product in the realm of outdoor power equipment, particularly known for its powerful performance and innovative features. As a part of Poulan's extensive lineup, this model combines reliability with user-friendly features, making it an excellent choice for both amateur gardeners and professional landscapers alike.

One of the key characteristics of the Poulan 954567833,186914 is its robust engine. Designed for efficiency and endurance, the engine provides ample power to tackle various landscaping tasks, from trimming grass to cutting through thick bushes. The model features a high-performance 2-cycle engine, which not only enhances its cutting power but also ensures that the machine is lightweight and easy to handle. This results in less fatigue for users during extended periods of use.

Another noteworthy feature of this model is its ergonomic design. The Poulan 954567833,186914 is equipped with a lightweight body that allows for greater maneuverability, making it easier to navigate tight spaces in gardens and yards. The soft-grip handles provide comfort during operation, reducing vibrations and enabling users to maintain a secure grip while working.

In terms of technology, the Poulan 954567833,186914 incorporates an advanced air filtration system. This system helps keep the engine clean and reduces the frequency of maintenance required, leading to longer intervals between servicing. The easy-access air filter makes routine maintenance a breeze for users, promoting longevity and efficiency.

The model also features a quick-release trimmer head, allowing users to swap out different cutting attachments seamlessly. This versatility makes it suitable for a wide range of applications, whether you’re dealing with overgrown grass or fine trimming around flower beds.

Fuel efficiency is another highlight of the Poulan 954567833,186914. Designed to be environmentally conscious, this model minimizes fuel consumption while maximizing power output. This not only saves on operational costs but also contributes to reduced emissions, aligning with modern sustainability practices.

In summary, the Poulan 954567833,186914 is a well-engineered outdoor power equipment choice that excels in performance, comfort, and environmental efficiency. With its powerful engine, ergonomic design, advanced technologies, and ease of use, it stands out as a reliable tool for all your landscaping needs.
Top Page Image Contents