Poulan DB18542YT manual Engine, Battery, Belts, Transaxle Cooling, Lubrication

Page 17

MAINTENANCE

CENTER HOLE

BLADE

5/8" BOLT OR PIN

FIG. 10

BATTERY

Your tractor has a battery charging system which is suf- ficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life.

•Keep battery and terminals clean.

•Keep battery bolts tight.

•Keep small vent holes open.

•Recharge at 6-10 amperes for 1 hour.

NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary.

TO CLEAN BATTERY AND TERMINALS

Corrosion and dirt on the battery and terminals can cause the battery to “leak” power.

•Remove terminal guard.

•Disconnect BLACK battery cable first then RED bat- tery cable and remove battery from tractor.

•Rinse the battery with plain water and dry.

•Clean terminals and battery cable ends with wire brush until bright.

•Coat terminals with grease or petroleum jelly.

•Reinstall battery (See “REPLACING BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual).

V-BELTS

CheckV-belts for deterioration and wear after 100 hours and replace if necessary. The belts are not adjustable. Replace belts if they begin to slip from wear.

TRANSAXLE COOLING

Keep transaxle free from build-up of dirt and chaff which can restrict cooling.

ENGINE

LUBRICATION

Only use high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade according to your expected operating temperature.

SAE VISCOSITY GRADES

 

 

 

 

 

 

 

 

 

 

SAE 30

 

 

 

 

 

 

5W-30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

F

-20

0

 

 

30 32 40

 

60

80

100

C

-30

-20

-10

0

10

20

30

40

TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE

oil_visc_chart1_e

FIG. 11

NOTE: Although multi-viscosity oils (5W30, 10W30 etc.) improve starting in cold weather, they will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil.

Change the oil after every 50 hours of operation or at least once a year if the tractor is not used for 50 hours in one year.

Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap/dipstick securely each time you check the oil level.

TO CHANGE ENGINE OIL (See Figs. 11 and 12)

Determine temperature range expected before oil change. All oil must meet API service classification SG-SL.

•Be sure tractor is on level surface.

•Oil will drain more freely when warm.

•Catch oil in a suitable container.

•Remove oil fill cap/dipstick. Be careful not to allow dirt to enter the engine when changing oil.

•Remove yellow cap from end of drain valve and install the drain tube onto the fitting.

 

OIL DRAIN VALVE

CLOSED

 

AND

 

LOCKED

 

POSITION

 

YELLOW CAP

DRAIN

TUBE

 

FIG. 12

•Unlock drain valve by pushing inward and turning counterclockwise.

•To open, pull out on the drain valve.

•After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown.

•Remove the drain tube and replace the cap onto to the bottom fitting of the drain valve.

•Refill engine with oil through oil fill dipstick tube. Pour slowly. Do not overfill. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this man- ual.

•Use gauge on oil fill cap/dipstick for checking level. Be sure dipstick cap is tightened securely for ac- curate reading. Keep oil at “FULL” line on dipstick. Tighten cap onto the tube securely when finished.

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Always Wear EYE Protection During Operation DB18542YTSafe Operation Practices for Ride-On Mowers Safety RulesGeneral Operation II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Contents of Hardware Pack Tools Required for Assembly AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Deck Levelness Check Tire PressureCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigReverse Operation System ROS Before Starting the Engine Mowing Tips Lubrication Chart MaintenanceGeneral Recommendations Before Each USEBlade Removal See Fig TractorTo Sharpen Blade See Fig Check Operator Presence SystemEngine BatteryBelts Transaxle CoolingCleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig Belt Installation To Level Mower HousingTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Adjust Brake To Check and Adjust Brake See FigTo Replace Motion Drive Belt See Fig To Check BrakeTo Adjust Steering Wheel ALIGN- Ment Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Choke Control To Adjust Throttle Control CableTo Adjust Carburetor To Replace FuseOther StorageFuel System Engine OILTroubleshooting Points Engine dies when Limited Warranty Policy Only Ride UP and Down Hill Not Across Hill Degrees MAX Suggested Guide for Sighting Slopes for Safe OperationParts and Service

DB18542YT specifications

The Poulan DB18542YT is a versatile and reliable garden tractor designed to handle a variety of landscaping tasks. Known for its durability and ease of use, this model is ideal for homeowners with medium to large yards.

One of the standout features of the DB18542YT is its powerful 18.5 horsepower Briggs & Stratton engine. This engine delivers ample power to tackle tough mowing conditions and ensures consistent performance throughout the mowing session. The efficient air-cooled design helps in maintaining optimal operating temperatures, enhancing the longevity of the engine.

Equipped with a 42-inch cutting deck, the DB18542YT allows users to cover more ground in less time, making it perfect for mowing larger lawns. The cutting deck also features a durable steel construction that is built to withstand the rigors of outdoor use. Furthermore, the deck height can be easily adjusted to achieve the desired grass length, offering versatility for different mowing conditions.

The Poulan DB18542YT includes a hydrostatic transmission, delivering a smooth and responsive driving experience. Unlike traditional gear-driven systems, this transmission allows for effortless speed adjustments without the need for manual shifting. This feature makes it easy for users to navigate around obstacles and varying terrain.

Another notable technology featured in this model is its mulching capability. With the optional mulching kit, users can efficiently recycle grass clippings, returning essential nutrients back into the soil. This not only promotes a healthier lawn but also reduces the amount of waste generated from mowing.

Comfort is also a priority in the design of the DB18542YT. The tractor comes with a comfortable high-back seat that provides excellent support during extended mowing sessions. Its user-friendly controls are strategically positioned for easy access, allowing the operator to focus on the task at hand without distraction.

In addition to mowing, the Poulan DB18542YT is compatible with a range of attachments, such as baggers and snow throwers. This adaptability enhances its functionality, making it a year-round gardening equipment solution.

In summary, the Poulan DB18542YT is a robust and feature-rich garden tractor that stands out for its powerful engine, efficient cutting deck, hydrostatic transmission, and versatile attachment options. Whether you're tackling mowing, mulching, or snow removal, this model delivers reliable performance for all your outdoor needs.
Top Page Image Contents