Poulan DB18542YT To Level Mower Housing, To Replace Mower Blade Drive Belt See Fig, Belt Removal

Page 20

SERVICE AND ADJUSTMENTS

TO LEVEL MOWER HOUSING

Adjust the mower while tractor is parked on level ground or driveway. Make sure tires are properly inflated (See “PRODUCT SPECIFICATIONS” section of this manual). If tires are over or underinflated, you will not properly adjust your mower.

SIDE-TO-SIDE ADJUSTMENT (See Figs. 15 and 16)

Raise mower to its highest position.

At the midpoint of both sides of mower, measure height from bottom edge of mower to ground. Distance “A” on both sides of mower should be the same or within 1/4" of each other.

If adjustment is necessary, make adjustment on one side of mower only.

To raise one side of mower, tighten lift link adjustment nut on that side.

To lower one side of mower, loosen lift link adjustment nut on that side.

NOTE: Each full turn of adjustment nut will change mower height about 1/8".

Recheck measurements after adjusting.

BOTTOM EDGE

 

BOTTOM EDGE

OF MOWER TO

 

OF MOWER TO

GROUND

 

GROUND

A

GROUND LINE

A

FIG. 15

SUSPENSION ARM

LIFT LINK

ADJUSTMENT NUT

FIG. 16

FRONT-TO-BACK ADJUSTMENT (See Figs. 17 and 18)

IMPORTANT: DECK MUST BE LEVEL SIDE-TO-SIDE. IF THE FOLLOWING FRONT-TO-BACK ADJUSTMENT IS NECESSARY, BE SURE TO ADJUST BOTH FRONT LINKS EQUALLY SO MOWER WILL STAY LEVEL SIDE-TO-SIDE.

To obtain the best cutting results, the mower housing should be adjusted so that the front is approximately 1/8" to 1/2" lower than the rear when the mower is in its high- est position.

Check adjustment on right side of tractor. Measure distance “D” directly in front and behind the mandrel at bottom edge of mower housing as shown.

Before making any necessary adjustments, check that both front links are equal in length.

If links are not equal in length, adjust one link to same length as other link.

To lower front of mower loosen nut “E” on both front links an equal number of turns.

When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nuts “F” against trunnion on both front links.

To raise front of mower, loosen nut “F” from trunnion on both front links. Tighten nut “E” on both front links an equal number of turns. The two front links must remain equal in length.

When distance “D” is 1/8" to 1/2" lower at front than rear, tighten nut “F” against trunnion on both front links.

Recheck side-to-side adjustment.

MANDREL

“D”

“D”

FIG. 17

BOTH FRONT LINKS MUST BE EQUAL IN LENGTH

NUT “F”

NUT “E”

TRUNNION

FRONT LINKS

FIG. 18

TO REPLACE MOWER BLADE DRIVE BELT (See Fig. 19)

The mower blade drive belt may be replaced without tools. Park the tractor on level surface. Engage parking brake.

BELT REMOVAL -

Remove mower from tractor (See “TO REMOVE MOWER” in this section of this manual).

Work belt off both mandrel pulleys and idler pulleys.

Pull belt away from mower.

BELT INSTALLATION -

Install new belt in reverse order of removal.

Make sure belt is in all pulley grooves and inside all belt guides.

Install mower in reverse order of removal instruc- tions.

20

Image 20
Contents DB18542YT Always Wear EYE Protection During OperationSafety Rules Safe Operation Practices for Ride-On MowersGeneral Operation II. Slope OperationIV. Towing ServiceIII. Children Table of Contents Contents of Hardware Pack Assembly Tools Required for AssemblyTo Remove Tractor from Carton Before Removing Tractor from SkidCheck Battery See Fig Check Tire Pressure Check Deck LevelnessCheck for Proper Position of ALL Belts Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor To Operate Mower See Fig To Adjust Gauge Wheels See FigReverse Operation System ROS Before Starting the Engine Mowing Tips Maintenance Lubrication ChartGeneral Recommendations Before Each USETractor Blade Removal See FigTo Sharpen Blade See Fig Check Operator Presence SystemBattery EngineBelts Transaxle CoolingCleaning To Remove Mower See Fig Service and AdjustmentsTo Install Mower See Fig To Level Mower Housing Belt InstallationTo Replace Mower Blade Drive Belt See Fig Belt RemovalTo Check and Adjust Brake See Fig To Adjust BrakeTo Replace Motion Drive Belt See Fig To Check BrakeTransaxle Gear Shift Lever NEUTRAL- Adjustment See Fig To Adjust Steering Wheel ALIGN- MentTo Start Engine with a Weak Battery See Fig Front Wheel TOE-IN/CAMBERTo Adjust Throttle Control Cable To Adjust Choke ControlTo Adjust Carburetor To Replace FuseStorage OtherFuel System Engine OILTroubleshooting Points Engine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

DB18542YT specifications

The Poulan DB18542YT is a versatile and reliable garden tractor designed to handle a variety of landscaping tasks. Known for its durability and ease of use, this model is ideal for homeowners with medium to large yards.

One of the standout features of the DB18542YT is its powerful 18.5 horsepower Briggs & Stratton engine. This engine delivers ample power to tackle tough mowing conditions and ensures consistent performance throughout the mowing session. The efficient air-cooled design helps in maintaining optimal operating temperatures, enhancing the longevity of the engine.

Equipped with a 42-inch cutting deck, the DB18542YT allows users to cover more ground in less time, making it perfect for mowing larger lawns. The cutting deck also features a durable steel construction that is built to withstand the rigors of outdoor use. Furthermore, the deck height can be easily adjusted to achieve the desired grass length, offering versatility for different mowing conditions.

The Poulan DB18542YT includes a hydrostatic transmission, delivering a smooth and responsive driving experience. Unlike traditional gear-driven systems, this transmission allows for effortless speed adjustments without the need for manual shifting. This feature makes it easy for users to navigate around obstacles and varying terrain.

Another notable technology featured in this model is its mulching capability. With the optional mulching kit, users can efficiently recycle grass clippings, returning essential nutrients back into the soil. This not only promotes a healthier lawn but also reduces the amount of waste generated from mowing.

Comfort is also a priority in the design of the DB18542YT. The tractor comes with a comfortable high-back seat that provides excellent support during extended mowing sessions. Its user-friendly controls are strategically positioned for easy access, allowing the operator to focus on the task at hand without distraction.

In addition to mowing, the Poulan DB18542YT is compatible with a range of attachments, such as baggers and snow throwers. This adaptability enhances its functionality, making it a year-round gardening equipment solution.

In summary, the Poulan DB18542YT is a robust and feature-rich garden tractor that stands out for its powerful engine, efficient cutting deck, hydrostatic transmission, and versatile attachment options. Whether you're tackling mowing, mulching, or snow removal, this model delivers reliable performance for all your outdoor needs.