Poulan PB18542LT Tools Required for Assembly, To Remove Tractor from Carton, Unpack Carton

Page 6

ASSEMBLY

Your new tractor has been assembled at the factory with exception of those parts left unassembled for shipping purposes. To ensure safe and proper operation of your tractor all parts and hardware you assemble must be tightened securely. Use the correct tools as necessary to insure proper tightness.

TOOLS REQUIRED FOR ASSEMBLY

A socket wrench set will make assembly easier. Standard wrench sizes are listed.

(1) 1/2" wrench

Utility knife

(2) 3/4" wrench

Tire pressure gauge

Pliers

 

When right or left hand is mentioned in this manual, it means when you are in the operating position (seated behind the steering wheel).

TO REMOVE TRACTOR FROM CARTON

UNPACK CARTON

•Remove all accessible loose parts and parts cartons from carton.

•Cut along dotted lines on all four panels of carton. Remove end panels and lay side panels fl at.

•Check for any additional loose parts or cartons and remove.

BEFORE REMOVING TRACTOR FROM SKID

ATTACH STEERING WHEEL (See Fig. 1)

ASSEMBLE EXTENSION SHAFT AND BOOT

•Slide extension shaft onto lower steering shaft.

•Place tabs of steering boot over tab slots in dash and push down to secure.

INSTALL STEERING WHEEL

•Position front wheels of the tractor so they are pointing straight forward.

•Remove steering wheel adapter from steering wheel and slide adapter onto steering shaft extension.

•Position steering wheel so cross bars are horizontal (left to right) and slide inside boot and onto adapter.

•Assemble large fl at washer, 5/16 lock washer, 5/16 hex bolt and tighten securely.

•Snap steering wheel insert into center of steering wheel.

•Remove protective materials from tractor hood and grill.

IMPORTANT: CHECK FOR AND REMOVE ANY STAPLES IN SKID THAT MAY PUNCTURE TIRES WHERE TRACTOR IS TO ROLL OFF SKID.

INSERT

5/16 HEX BOLT

5/16 LOCK

WASHER

LARGE FLAT

WASHER

STEERING

WHEEL

STEERING

BOOT

TABS

ADAPTER

EXTENSION

SHAFT

LOWER

STEERING

SHAFT

TAB

SLOTS

FIG. 1

INSTALL SEAT (See Fig. 2)

Adjust seat before tightening adjustment knob.

•Remove adjustment knob and fl at washer securing seat to cardboard packing and set aside for assembly of seat to tractor.

•Pivot seat upward and remove from the cardboard pack- ing. Remove the cardboard packing and discard.

•Place seat on seat pan so head of shoulder bolt is positioned over large slotted hole in pan.

•Push down on seat to engage shoulder bolt in slot and pull seat towards rear of tractor.

•Pivot seat and pan forward and assemble adjustment knob and fl at washer loosely. Do not tighten.

•Lower seat into operating position and sit on seat.

•Slide seat until a comfortable position is reached which allows you to press clutch/brake pedal all the way down.

•Get off seat without moving its adjusted position.

•Raise seat and tighten adjustment knob securely.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents PB18542LT Always Wear EYE Protection During OperationGeneral Operation Safety RulesSafe Operation Practices for Ride-On Mowers II. Slope OperationIII. Children ServiceGeneral Service IV. TowingTable of Contents Contents of Hardware Pack To Remove Tractor from Carton AssemblyTools Required for Assembly Before Removing Tractor from SkidCheck Battery See Fig Check for Proper Position of ALL Belts Check Tire PressureCheck Deck Levelness Check Brake SystemOperation Know Your Tractor HOW to USE Your Tractor Reverse Operation System ROS To Adjust Gauge Wheels See FigUsing the Reverse Operation System To Operate Mower See FigBefore Starting the Engine Mowing Tips Lubrication Chart MaintenanceMaintenance Schedule General RecommendationsTractor Blade Removal See FigTo Sharpen Blade See Fig Belts BatteryEngine Transaxle CoolingCleaning Service and Adjustments To Install Mower See FigTo Remove Mower See Fig To Replace Mower Blade Drive Belt See Fig To Level Mower HousingBelt Installation Belt RemovalTo Replace Motion Drive Belt See Fig To Check and Adjust Brake See FigTo Adjust Brake To Check BrakeTo Start Engine with a Weak Battery See Fig Transaxle Gear Shift Lever NEUTRAL- Adjustment See FigTo Adjust Steering Wheel ALIGN- Ment Front Wheel TOE-IN/CAMBERTo Adjust Carburetor To Adjust Throttle Control CableTo Adjust Choke Control To Replace Headlight BulbFuel System StorageOther Engine OILTroubleshooting Points Problem Cause CorrectionEngine dies when Limited Warranty Policy Suggested Guide for Sighting Slopes for Safe Operation Only Ride UP and Down Hill Not Across Hill Degrees MAXParts and Service

PB18542LT specifications

The Poulan PB18542LT, a robust and versatile lawn mower, has gained popularity among homeowners for its effective design and user-friendly features. This powerful machine utilizes a solid 18.5 HP Briggs & Stratton engine, ensuring reliable performance for various grass lengths and terrains. Whether tackling a small yard or a larger property, the PB18542LT's powerful engine makes effortless work of even the toughest lawns.

One of the standout characteristics of the PB18542LT is its 42-inch cutting deck. This larger cutting width allows for more efficient mowing, reducing the time needed to complete yard work. The deck is designed for optimal airflow and grass clipping distribution, ensuring a clean and even cut every time. The machine supports various cutting height adjustments, typically ranging from 1 to 4 inches, allowing users to customize their cut according to their lawn's specific needs and seasonal variations.

Technology-wise, the Poulan PB18542LT features an automatic transmission system, which provides seamless operation and comfortable maneuverability. This feature eliminates the need for constant gear shifting, allowing users to focus more on mowing rather than managing speeds. The steering capability of the mower is enhanced, making it easy to navigate around tight corners and obstacles in the yard.

Durability is another key aspect of the PB18542LT, constructed from high-quality materials that withstand the rigors of regular use. The mower's heavy-duty frame contributes to its stability and longevity, ensuring that it can tackle diverse landscapes without compromising its performance.

Additional conveniences include an easy-to-access fuel tank, a comfortable seat designed for extended operation, and a user-friendly control panel that allows for quick adjustments. The inclusion of a mulching capability allows for efficient grass recycling, reducing the need for bagging and promoting a healthier lawn.

In summary, the Poulan PB18542LT is a feature-rich riding lawn mower designed for durability and efficiency. With its powerful engine, larger cutting deck, and innovative technologies, it combines performance and user comfort effectively. Whether you are a seasoned gardener or a first-time buyer, the PB18542LT stands out as a reliable choice for maintaining your lawn with ease.
Top Page Image Contents